I'm going to wait for the right o-rings. Hopefully we hear back from Bruce soon.
Iatty
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
Just for a visual reference, this is how my o ring fits on the mouthpiece. Everything is working fine, even with just the one o ring on the ceramic cup. As long as all the areas that need to be sealed are sealed, the iAtty should not leak.
This is how mine looks as well. The o-ring fits tightly to the cone tube and there is a little bit of room around it but the hole in the top cap that the cone tube comes up out of is sealed. I use the tube from a bible dry highlighter refill that I had in my desk. It's the right size to push down into the top cap to seat the o-ring on the cone tube. I put the other small fat o-ring first onto the ceramic followed by the thinner o-ring that came loose in the pack.
Yep. Not the ones I received but I have everything going fine with my setup. I will just order these correct sizes from McMaster and have many spares.
Maybe it helps someone here. I got mine from Krom. And the o-rings were like Imeo told. A very small one, a little bigger one and a little fatter one. I put the fatter one under the mouthpiece...and, because I was afraid to destroy the ceramic I checked my hardware and found the second part to little bigger one in my fog. So I put 2 o-rings of the same size on the ceramic an it works nice
Last edited:
I got mine from cov and the I rings were the same size on the ceramic but it fit fine. Didn't have vasaline so I used a little pg for lube. Took a little twisting and some pressure but it went in.
How will it come out? With the o-ring I used on the top cap, the smaller one, it seals against the cone tube and there is space all around it so the juice washes over the top of the seal (because the mouth piece is off) and into the indention where a bigger o-ring would be seated. But it sounds like some of us received different sizes of o-rings. I do want to use the ones you say are supposed to be in there so I'm going to order some on Monday so I have everything setup as you designed. You're the expert here.
I just left one o-ring outside because I could only get one in. Made my first wire at around 1.3ohm lol, it was a little work because I have big hands and they don't do well with very small wire. I tried it on my Provari but was getting errors because of the safety system they have. I put it on my GGTS and I'm vaping clouds and it's hitting great. The taste isn't 100% yet but it's getting better. First time and it's not bad at all, great job Imeo.
How will it come out? With the o-ring I used on the top cap, the smaller one, it seals against the cone tube and there is space all around it so the juice washes over the top of the seal (because the mouth piece is off) and into the indention where a bigger o-ring would be seated. But it sounds like some of us received different sizes of o-rings. I do want to use the ones you say are supposed to be in there so I'm going to order some on Monday so I have everything setup as you designed. You're the expert here.
Mouthpiece keeps o-ring in place Repent. If you take off the mouthpiece then the o-ring is not secured and its not pressed against cap so it will come out very easy
I did the first wire wrong. I thought you said something else in your video and I had to take it all apart. I'm happy it's not that much work. My o-ring isn't sealing the gap under the mouthpiece, is that a problem? I don't think it's big enough. Also the cone top wasn't directly in the middle but I bent it very very softly to make it in the middle. It's working right now and I've only had a little juice in the mouth once. It looks very good on the ssggts and works well without the top cap of the collector tank. The air control is working perfect but I'm hoping it doesn't scratch the bottom of the iAtty when I put it on the GGTS. I know this is only my first time trying everything and I know it will get better every time after this one. I'm happy Imeo.
Just finished my first tank. This is my first GG product and I must say it's pretty impressive. I did have a little trouble getting the ceramic installed but no biggie, just have to make sure the proper orings are installed the next time I take it apart.
I had no leaks whatsoever, no flooding, no dry hits and the tank vaped till it was bone dry, which was nice cause I wasn't sure how to tell when the tank would be getting low. As it turns out there was just a sudden drop in vapor and the tank was completely empty, no need to see the liquid.
So I give a
to Imeo for a job well done and am looking forward to purchasing another IAtty and hopefully a GGTS in the near future. Nice work Imeo.
I had no leaks whatsoever, no flooding, no dry hits and the tank vaped till it was bone dry, which was nice cause I wasn't sure how to tell when the tank would be getting low. As it turns out there was just a sudden drop in vapor and the tank was completely empty, no need to see the liquid.
So I give a
to Imeo for a job well done and am looking forward to purchasing another IAtty and hopefully a GGTS in the near future. Nice work Imeo.
I think Bruce may be putting the Wick, R-Wire and NR-Wire on his site. Don't quote me on this though
thanks again silentt
I want to thank you too my new friend bacc. I am glad that you are totally satisfied with Iatty
I want to thank you too my new friend bacc. I am glad that you are totally satisfied with Iatty
Time for dinner, so I'll call it a day and get a fresh start tomorrow. I did get a ce2 cup ringed and in there so I made progress, thanks for the tip Z.
- Status
