And, besides Rule's perfect explanation pls see also this:
Instagram photo by @nazrisaid (nazri said) | Statigram
- Status
And, besides Rule's perfect explanation pls see also this:
Instagram photo by @nazrisaid (nazri said) | Statigram
r u using nr leads? they look a whitish color??? or is just the photo?
Yeah, gotta have coffee, when doing set ups. I'm still fooling around with the new ios7 on my phone, and syncing my pics with icloud to my laptop. Obviously, I'm better with coils and wicks, than I am with computers.
Some say sub-ohm is an extreme sport. It's nothing compared to coiling coils prior to coffee.
I ordered these:
008 PTFE O-Ring, 55D Durometer, White, 3/16" ID, 5/16" OD, 1/16" Width (Pack of 10): Amazon.com: Industrial & Scientific
Pretty sure they are the right size, and from what I've been able to find, PFTE is the best material for resistance to both Citric and Malic Acid. I get them on Tuesday, so we shall see ^_^.
Ok guys. Got a question. Just ordered a KFL and it should be here any day. I also have a Diver for which I have a lot of NR-R-NR ready wires.
Is it possible to use these in a KFL? I know it's not mandatory but will it work?
Is it possible to use these in a KFL? I know it's not mandatory but will it work?
Congrats on the K-Lite purchase. With regards to your question, I don't see how you would use the NR-R-NR wires in the K-Lite. The posts are more like a RDA so are barely about 1/2 inch apart.
Let's see what the experts have to say about it.
You can use the ready wires for sure, but I see no reason to really.. Unless you got rid of the Diver and want to use them for something
Oh my...the flavor and vapor on the K-Lite is amazing!!! However, I just wrapped a 1.2ohm microcoil with cotton, and two problems popped up, first time I filled it, juice was pouring out of the air inlet, so I took it apart and put it back together, filled it again and juice poured out of the driptip. Any clues on what I'm doing wrong?
Try filling it like I do, from the top. I remove the topcap, tighten the chimney that got unscrewed when removing topcap.
Place a finger on the airhole, and fill her up.
Put the topcap back on, but just one thread or so, turn it upside down, remove finger from airhole and secure the cap.
If any gurgling, hold upside down and blow through air hole.
something isn't sealing properly, most likely the oring (4c) in the topcap.
I feel like i'm some kind of kfl oring 4c ambassador. I'm gonna go make a badge...
I never tried it Blix's way. I'm sure it works. I always invert-fill (upside down). I think BC is correct...you haven't got all the segments seated all the way. Ensure you are snugged up and filling upside down should be no problem. I use a 5ml syringe with 18ga blunt tip. But similar will work. Tilt upside down at a 45 degree angle. Fill until you get a pea-sized air bubble at the top of your viewing window segment. Screw fill hole and you should be good to go. Never had a problem doing it this way.
This is the exact one I use. There are others. It will fill and unfill your KFL.
Pack of 10 x 5 ml Syringes Blunt Tip 18g Draw Stick not Needle No Skin Injection | eBay
This is the exact one I use. There are others. It will fill and unfill your KFL.
Pack of 10 x 5 ml Syringes Blunt Tip 18g Draw Stick not Needle No Skin Injection | eBay
No need for a syringe if your bottle has a nipple top that fits in the bevel of the screw hole. Just push bottle against the fill hole to make a seal and squeeze. I put the device at 45 degrees and fill until the air bubble just reaches the bottom metal section.
That was it, thank you gentlemen, this thing absolutely rocks!!! I fear that after I get my Russian 91%, I might not have to buy anything else...
BTW, regarding battery life with the Kayfun, I've been running a 1.6ohm coil on mine for the past 3 days. I bought two eFest 18500's and two 18350's and I gotta say, the 18350 saw me through the entire day yesterday. I was afraid I'd have to change it every 4 hours but by the end of the day (started using it at 7am, ended at 12 midnight) I still had 3.68v on it. I had gone through an entire tank of Gorilla Juice on the KFL with this battery.
The 18500 ended my previous day at 3.9v with the same amount of juice consumed.
I'm guessing all these cries of low battery life come from sub ohm vapers, but I don't think I see a need to go lower than 1.6ohm for my tastes. I guess I'll order 28awg Kanthal and try a 1.0ohm coil to see if I need the extra heat.
The 18500 ended my previous day at 3.9v with the same amount of juice consumed.
I'm guessing all these cries of low battery life come from sub ohm vapers, but I don't think I see a need to go lower than 1.6ohm for my tastes. I guess I'll order 28awg Kanthal and try a 1.0ohm coil to see if I need the extra heat.
I seriously get more vapor (and flavor) from a 3 second inhale on this than I do a 7 second inhale with a ZAP.
No need for a syringe if your bottle has a nipple top that fits in the bevel of the screw hole. Just push bottle against the fill hole to make a seal and squeeze. I put the device at 45 degrees and fill until the air bubble just reaches the bottom metal section.
Some juices have eye droppers and not nipple tops. Yes, you could get bottles with the tips but then at 85 cents/syringe....
- Status
Similar threads
