Kayfun LITE

[vapdivrr]

The hole seems very close to the upper portion of the deck, you know what I mean ? Also does that hole in the 510 have anything to do with air flow?


Also to the peeps I had this issue where I had to wash my Russian 5 or 6 times and I still couldn't get the taste out. I washed my new kfl clone once with hot water dawn and a toothbrush no problems.

sorry, not sure what you meant by upper portion hole. The 510 center post does have some control of airflow. what happens is this, the 510 post is basically a screw that connects to the positive block. about half way up from the actual 510 threads, this 510 screw has a hole thru the center, and from this hole to the positive block the 510 post is hollow. This hole accepts air from the main air hole and carries it to the coil. If this 510 center post hole isn't lined up correctly, the flow of air can be reduced. to line this up, or to check it, you can stick a small needle into the side main air hole and see if it continues all the way thru. If it doesn't, then you may need to slightly tighten the 510 screw. you really cannot loosen the 510 screw because the positive block will loosen but sometimes a slight tight can open the draw a little.

Sent from my SCH-I545 using Tapatalk

 

[qorax]

28g Kanthal, 2mm Bit, 11 wraps, 1.2Ω

= 21 Watts Fun

 

[Rossum]

1.2Ω strikes me as surprisingly low for 11 wraps of 28 gauge Kanthal on a 2mm bit. I'm usually at 1.3 - 1.4 with just 8/9 wraps on a 5/64" (1.98mm) bit.

 

[qorax]

1.2Ω strikes me as surprisingly low for 11 wraps of 28 gauge Kanthal on a 2mm bit. I'm usually at 1.3 - 1.4 with just 8/9 wraps on a 5/64" (1.98mm) bit.

It shows 1.2Ω on both my Provari and the WAE. However, shows 1.24Ω on the Atty Tester

 

[Bronze]

1.2Ω strikes me as surprisingly low for 11 wraps of 28 gauge Kanthal on a 2mm bit. I'm usually at 1.3 - 1.4 with just 8/9 wraps on a 5/64" (1.98mm) bit.

I was gonna say the same thing. If I did it, it would be 1.6 ohms.

 

[Fir3b1rd]

I was gonna say the same thing. If I did it, it would be 1.6 ohms.

I use a 2mm rod and 9 wraps gives me 1.355 on the HDMM and 1.4 on my p-thingie

 

[Bronze]

I use a 2mm rod and 9 wraps gives me 1.355 on the HDMM and 1.4 on my p-thingie

2mm at 9 wraps...yep, I'd get the same as you. Q lives in Canada though and they have that funky math system up there. He's probably measuring in imperial ohms or something.

What's a liter? A quart and a liter bit more?

 

[ricks]

How long can silica last? I've been using the same pieces of silica in both my everyday Kayfuns for more than 9 fills. I use 4ml to fill them. I clean and dry burn my wicks every 4 or 5 fills. Still vaping and tasting great. Love these things.

 

[dwcraig1]

How long can silica last?

I've gotten more than 30 days, it usually still looked like it would go 30 more but I'd change it anyway.

 

[Bronze]

How long can silica last? I've been using the same pieces of silica in both my everyday Kayfuns for more than 9 fills. I use 4ml to fill them. I clean and dry burn my wicks every 4 or 5 fills. Still vaping and tasting great. Love these things.

My silica wick lasted 5+ months...aprox 400 - 500 mls before it was too frayed to use anymore. I clean/burned after every three tanks. Actually, it still worked but when you think about how easy it is to rebuild I had to ask myself, why?

 

[qorax]

2mm at 9 wraps...yep, I'd get the same as you. Q lives in Canada though and they have that funky math system up there. He's probably measuring in imperial ohms or something.

What's a liter? A quart and a liter bit more?

Yep, the bloody thing is 2mm. And you guys are right, it should be 1.4Ω+. What's going wrong? Have I used 26g in place of 28

 

[ricks]

I used to top them off when they got low but it sometimes made the liquid get a little dark. Now I vape them empty to prevent it. Best vape so far.

 

[Jdbaker82]

Yep, the bloody thing is 2mm. And you guys are right, it should be 1.4Ω+. What's going wrong? Have I used 26g in place of 28

how's 26 Guage work in a kayfun?

Sent from my SCH-I545 using Xparent Skyblue Tapatalk 2

 

[Bronze]

Yep, the bloody thing is 2mm. And you guys are right, it should be 1.4Ω+. What's going wrong? Have I used 26g in place of 28

I think you used rebar.

 

[vapdivrr]

Yep, the bloody thing is 2mm. And you guys are right, it should be 1.4Ω+. What's going wrong? Have I used 26g in place of 28

must be 26 q, because I have to agree on the majority here, 11 wraps of 28g should be in the 1.4 to 1.6 range

Sent from my SCH-I545 using Tapatalk

 

[Bronze]

how's 26 Guage work in a kayfun?

Sent from my SCH-I545 using Xparent Skyblue Tapatalk 2

Diver uses 26 gauge (he just spoke about it earlier today). Ask him how he built it. He said it has its place.

 

[Bronze]

Diver uses 26 gauge (he just spoke about it earlier today). Ask him how he built it. He said it has its place.

EDIT: Speak of the devil.

 

[vapdivrr]

how's 26 Guage work in a kayfun?

Sent from my SCH-I545 using Xparent Skyblue Tapatalk 2

sure it will, the question is what mod runs it better

Sent from my SCH-I545 using Tapatalk

 

[vapdivrr]

It was so bad I sent the Russian back. Also running a 1.6 ohm coil in mine extremely flavorful hard TH but not a lot of vapor? What's the highest I should push this thing wattage wise?

wattage on a 1.6 ohm coil? I would say in the 4.7v range. but really depends on how well you have it wicking and what wire gauge.

Sent from my SCH-I545 using Tapatalk

 

[vapdivrr]

Qorax, maybe it's nichrome wire.

Sent from my SCH-I545 using Tapatalk