Mark Bugs Bottom Feeding Rebuildable Atomizer (prototype) initial impressions

Status
Not open for further replies.

Roxxette

Ultra Member
ECF Veteran
Verified Member
Feb 4, 2012
1,535
656
Caribbean
Ok so I took the coil off the wick that came with the Chalice (it's obviously much too thin because it took me around 20 minutes to put the coil through the holes).

The first time I wrapped it, it measured 7.7ohms :ohmy: Yup, really awful job done by me. So I took the coil off and I'm not really sure what I did with it but this time it read 3.3ohms.

Does this remotely look anything like it's supposed to look? :blink:

IMG_20120814_184242.jpg

Try to have your coils closer but they cant be touching the other wire or it they will short, hmm 7.7ohm ? Really what wire are you using ?
 

rondasherrill

Ultra Member
ECF Veteran
May 19, 2012
2,247
1,941
Valhalla
Where is the best place to pick up Cotton Wick?

Walmart has THIS cotton yarn in plain white that works great.

Walmart also has THIS crochet thread that works great. Get the size 3. It's about the same size as 1mm silica wick.

You can get THIS candle wick on eBay cheap. Works great, but it's a little thicker. You would want the #1/0
 

MXBNW

ECF Guru
ECF Veteran
Verified Member
May 15, 2010
10,355
6,745
NW Washingtion
www.e-cigarette-forum.com
Thanks I will make a run to Walmart this week. I may have some candle wick around here from way back but need to do some digging. I got tons of wick and wire of all types but wont to try the Cotton out.

Thanks


Walmart has THIS cotton yarn in plain white that works great.

Walmart also has THIS crochet thread that works great. Get the size 3. It's about the same size as 1mm silica wick.

You can get THIS candle wick on eBay cheap. Works great, but it's a little thicker. You would want the #1/0
 

rondasherrill

Ultra Member
ECF Veteran
May 19, 2012
2,247
1,941
Valhalla
Thanks I will make a run to Walmart this week. I may have some candle wick around here from way back but need to do some digging. I got tons of wick and wire of all types but wont to try the Cotton out.

Thanks

If you have cotton wick around already, make sure that it is unprimed... You do not want to vape a wick with wax or anything else in it.

Quick question with the cotton. Do you wash it first or just use it as is.

I am sure this has been talked about but work has me running right now and I have no time to go back and read.
Most people suggest boiling it to remove any sizing that might be on it. I don't boil it, but I do drip some plain VG on the new wick and do a couple "wet burns" before I vape with it.
 

MXBNW

ECF Guru
ECF Veteran
Verified Member
May 15, 2010
10,355
6,745
NW Washingtion
www.e-cigarette-forum.com
Got it :) Doing the happy dance.

Fired it up using the standard with and wire. Not bad at all.

Came set at 1.8-1.9 set the VVG at 4.2 its vaping like a monster.

Easy to juice. It looks like you can not flood it. juice just runs back down the tube.

I would sugest and I do this every day. Change out your bottles when you refill this will keep any carbon from backing down in to the bottle and building up. Not sure if this will happen with this atty but it will be keeping a close watch on it over the next few days.

Love the draw its just right. flavor is good should get better as the wire brakes in.

I will play with new wick and wire latter this week after I run this through its paces.

I will post photos latter this evening. I did take the metal DT off, I am not a fan of matel DT's but it is a nice DT. :)
 

house mouse

Vaping Master
ECF Veteran
Verified Member
Oct 24, 2010
3,063
8,984
BFE
Not cool :( can you chase them down.

No, I'm cooking dinner right now. I'll run up there and pick it up tomorrow. It just sucks cause I've been here all day. He must have come around in stealth mode today cause the hound didn't throw her usual "I'm going to kill you" barking fit.
 

MXBNW

ECF Guru
ECF Veteran
Verified Member
May 15, 2010
10,355
6,745
NW Washingtion
www.e-cigarette-forum.com
That sucks, Our two pups always let me know when the mail is here. I think there is something with the truck that sets them off.

Keep up posted. this atty is a nice one. :)


No, I'm cooking dinner right now. I'll run up there and pick it up tomorrow. It just sucks cause I've been here all day. He must have come around in stealth mode today cause the hound didn't throw her usual "I'm going to kill you" barking fit.
 

Keekers

Ultra Member
ECF Veteran
Verified Member
Feb 2, 2011
2,855
3,921
Michigan
ok so my Provari is reading 2ohms when I check the atty. I dripped some VG on it and fire to test it out. It crackles and the wire is turning dark brown but I don't see any coils getting red. Am I just not firing it long enough? I had an atty pop in my eye once so I've ever since been traumatized of popping another one.
 

Keekers

Ultra Member
ECF Veteran
Verified Member
Feb 2, 2011
2,855
3,921
Michigan
The coils will never glow while they are wet. If it reads 2ohms and produces vapor, it's good.

EDIT: In fact, if you are using cotton, you do NOT want the coils to glow. Glowing coils = burned cotton = BAD taste.
Thank you for responding!!!!
I tried to vape it but haven't gotten any flavor. I think I need to burn some of the VG off.
xoxo I started to feel like a little lonesome
 
Last edited:
Status
Not open for further replies.

Users who are viewing this thread