Micro Coil for the RBA on your REO

[pdib]

BTW: XOxo, you've put me in a rather awkward position! I have been thoroughly confident that my 3 Grands were all I'd ever need. Now I've got this exquisite NEMP* which does not have a home! I've been dripping it; but, if I ever decide to take it on the go . . . . . .. ?











*Naturally Extracted Monkey Poo

 

[gmb225]

so i got my new rm2 today, noticed while building it that yes it has 2 sets of small holes for the taller post so i can build dual coils i i want. though they go thru 90 degrees from each other. i could screw it down and tighten both wires at the same time. not going for dual coils but could if i wanted to. will post pics their not real clear but u can see.

 

[BigCloudz]

so i got my new rm2 today, noticed while building it that yes it has 2 sets of small holes for the taller post so i can build dual coils i i want. though they go thru 90 degrees from each other. i could screw it down and tighten both wires at the same time. not going for dual coils but could if i wanted to. will post pics their not real clear but u can see.View attachment 252159View attachment 252160

Can you fit a single piece of 26g through either hole?

 

[MamaTried]

BTW: XOxo, you've put me in a rather awkward position! I have been thoroughly confident that my 3 Grands were all I'd ever need. Now I've got this exquisite NEMP* which does not have a home! I've been dripping it; but, if I ever decide to take it on the go . . . . . .. ?











*Naturally Extracted Monkey Poo

poo seems like a perfectly good reason to get another Reo to me...








... crap. now i have poo envy


EDIT: hold on... i can say crap but the monkey can't fling poo??? what's up with that?

 

[gmb225]

Can you fit a single piece of 26g through either hole?

28g is all i have and the hole is just a little bigger so not sure, but easy to drill out if i couldn't.

 

[BigCloudz]

28g is all i have and the hole is just a little bigger so not sure, but easy to drill out if i couldn't.

Gotcha. Yea mine was teeny tiny. I work in a machine shop atmosphere (not an old fashion machine shop, but a lot of similar equipment), and I still found it a challenge to open up the holes. I was just going to pull the post out, put it in a pin vice and wire EDM the hole to the exact diameter I want. However my Wire was in use Sat so I just did it by hand. It worked, but the holes are not completely symmetrical, which bothers me as an OCD mold maker..haha

 

[moondragon]

Just got home from a work meeting and found a package with my RM2 in it Getting all my supplies together, going to watch the video tutorial one more time, check the post with gauge, diameter and wrap #'s, and then give it a try.

 

[gmb225]

i know i said i wasnt gonna do it but...

not the prettiest build i overscrunched the coils messed them up a bit then fixed them. but it works .7ohms. hell of a vape with 1 stock airhole but im just payin...

 

[Vapeaddikt]

The coil towads the backside seems a bit close to the cap for comfort. I just hope it doesn't short on you.

 

[gmb225]

The coil towads the backside seems a bit close to the cap for comfort. I just hope it doesn't short on you.

yea its all good and tight and inside the lip should be ok. gives me a warmer vape and more flavor but same vape production. guess its cause just one airhole and voltage drop went from .4v to .67v. tomorrow i think ill redue it back to single coil. not gonna drill more airholes thats for sure.

 

[darkzero]

The coil towads the backside seems a bit close to the cap for comfort. I just hope it doesn't short on you.

I think the other way around......the other coil is too far from the lip (assuming there was another air hole). You'd probably freak with my coil placement, I like mine hugging the air hole.

 

[Xobeloot]

BTW: XOxo, you've put me in a rather awkward position! I have been thoroughly confident that my 3 Grands were all I'd ever need. Now I've got this exquisite NEMP* which does not have a home! I've been dripping it; but, if I ever decide to take it on the go . . . . . .. ?










*Naturally Extracted Monkey Poo

Lol! Now every time my squonk gurgles, i'm going to think of NEMP!

I am glad you are enjoying it. I'll have to make a large batch and ship it to you before i deploy so you can talk it up and send out little samples (on my dime of course).

Maybe by the time I get home there will be a demand for the stuff (probably not though)

Hey! Orangutans have dreams too!

As for what to put it in...

I'm considering another reo and possibly that thing that SX mentioned earlier


Sent from the zoo using Tapatypo 2

 

[moondragon]

Interrupting the fancy builds for a minute...

to bring you my first build and it works





Now back to the regularly scheduled crazy sub-ohm double, triple or other fantastic builds of technical prowess...

 

[pdib]

Nice work, Moondragon!

 

[pdib]

Trusted bumblebee found floating in pool of sample juice.

Orangutan [shaking head] says, "never again . . . .. "

 

[moondragon]

Nice work, Moondragon!

Thanks, and a big thanks to all of you here for the wonderful tutorials, videos of builds and all the pictures and posts! They really helped a lot!

 

[Vapeaddikt]

Looking good Moon!

 

[Xobeloot]

Great stuff moon! I'm loving the purple reo too!


Sent from the zoo using Tapatypo 2

 

[super_X_drifter]

Moondragon your setup looks boss. Great job. Glad to see your vaping like the Rockstar that you are

 

[moondragon]

You all made it so easy to figure out.