New studies find carcinogens in vg and pg at high temps, even in tootle puffers

[homeuser6]

mike, could you get a temp reading of a 3mm ekowool/3mm coil/30g or 32g/2 ohm? half ohm is surely not considered tootle puffing. or am i the only vaper that does this? (tube mech). i really like your empirical testing but it has not seemed relevant to my style so far.

 

[retired1]

mike, could you get a temp reading of a 3mm ekowool/3mm coil/30g or 32g/2 ohm? half ohm is surely not considered tootle puffing. or am i the only vaper that does this? (tube mech). i really like your empirical testing but it has not seemed relevant to my style so far.

You aren't the only one. I, too, refuse to join the sub ohm craze.

 

[Verb]

mike, could you get a temp reading of a 3mm ekowool/3mm coil/30g or 32g/2 ohm? half ohm is surely not considered tootle puffing. or am i the only vaper that does this? (tube mech). i really like your empirical testing but it has not seemed relevant to my style so far.

The resistance has little significance here. He was using a coil of a similar mass to what you vape and in the same power range.

 

[mikepetro]

mike, could you get a temp reading of a 3mm ekowool/3mm coil/30g or 32g/2 ohm? half ohm is surely not considered tootle puffing. or am i the only vaper that does this? (tube mech). i really like your empirical testing but it has not seemed relevant to my style so far.

I only used SS430 because I wanted to see what the DNA would do with it in TC mode. That wasnt meant to replicate tootle, just to compare rayon/silica.

I am sure I have some wire around to accomplish this. Heck, I have NI, TI, TU, SS316, SS430, Nichrome, Kanthal, Ribbon wire, and a few more I cant remember. Various gauges of each, mostly the popular gauges of the time. Anyway, I am sure I could replicate the coil, but it would have to be in a modern atty like a Merlin. juice flow restricted or open? Airflow restricted or open?

The one problem I forsee is it sounds like you might be a dripper. I am not tackling drippers or squonkers. Only tanks. I do not have the experience with dripping or squonking to maintain the user discipline in anything that I would consider a consistent or repeatable manner. At least not enough that I would hang my name on a test and call it credible.

 

[homeuser6]

kanthal in an rsst, 4-1mm air holes. i suppose one big hole like most use would be similar


https://www.e-cigarette-forum.com/f...167e6c434bced01cb0a16b370308d6.jpg?1478450048

 

[mikepetro]

kanthal in an rsst, 4-1mm air holes. i suppose one big hole like most use would be similar

I dont have an RSST laying around anymore, but I do still have a few GKMFs, Would that be suitable. It was one of the best Gennys in its day.

I also just found this in my desk drawer at work. The wick hole is drilled out to 3mm. I forget the name, it was a Shek Co-op deal.

 

[mikepetro]

GKMF with dual ceramic wicks:
Gawd that brings back memories.......

 

[mikepetro]

Are you doing a "U" wick, or a straight wick like in my pics?

 

[Ragnar94]

Yeah but even so it won't be anything like fags, that stuff is NASTY

 

[homeuser6]

yes, any genny would be close if the air was more open than stock

 

[mikepetro]

You aren't the only one. I, too, refuse to join the sub ohm craze.

I dont consider myself a sub ohmer either. The only reason I went there was for TC.

I think TC changed the definition of subohm.

 

[mikepetro]

yes, any genny would be close if the air was more open than stock

View attachment 665721

I will see what I have. I am not going to drill any of my atties, but I think there is a good chance I have a GKMF cap with dual 2mm airholes.

 

[homeuser6]

 

[mikepetro]

View attachment 665723

Gotcha....

 

[homeuser6]

I will see what I have. I am not going to drill any of my atties, but I think there is a good chance I have a GKMF cap with dual 2mm airholes.

that should be pretty close

 

[mikepetro]

that should be pretty close

Or......

The other option is build one up exactly like you like it, send it to me, with $7 to cover return postage, and I will test your exact atty.

 

[homeuser6]

way cool,can you pm me an address? i'll include some juice since it has dw added

 

[mikepetro]

way cool,can you pm me an address? i'll include some juice since it has dw added

PM sent....

 

[mikepetro]

Or......

The other option is build one up exactly like you like it, send it to me, with $7 to cover return postage, and I will test your exact atty.

Just for the record. While I am willing to do this, for atty types that I dont have on record, dont assume I can do ANYTHING. You have to let me know the atty first so I can look it up.

In this case, I have had several RSSTs so I know the atty, and I know I can do my magic on it.

There are some I wont attempt. For example the Eleaf GS series stuff. While not impossible, they would be way more complicated to do, more complicated than I care to mess with.

 

[GeorgeS]

I dont consider myself a sub ohmer either. The only reason I went there was for TC.
I think TC changed the definition of subohm.

Actually I think anything "regulated" changed the meaning of "subohm".

Then again, all my "subohm" builds are with TC wire and used primarily on TC enabled devices. (there are some exceptions)