Odysseus official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- halo madvapes provari revolution
- Status
Q for those with the upgrade kits.
what is the tiny o-ring for (looks around 5x2)
i've not seen it used in any vids,
saying that though i've seen the 510/e2 connector in the vids and presume this o-ring may be for insulation of the positive pole even though its very tight fit. am i right???
what is the tiny o-ring for (looks around 5x2)
i've not seen it used in any vids,
saying that though i've seen the 510/e2 connector in the vids and presume this o-ring may be for insulation of the positive pole even though its very tight fit. am i right???
thats what I'm thinking it must be for, couldn't find any other thing so rammed it on there
If you mean the 6x1,5 o-ring, it goes on the threads of the CE2 atomizer to cover its side holes Oddy
On the other hand if you mean the tiny o-ring that we put between ceramic metal housing and center pole, then we put this on center pole (at its end, where is has a small channel) only when you use Ody inside UFS. Also we remove the o-ring under the center pin of Ody (that it seals the 510 hole) when we are in UFS mode
I put the tiny tiny one between the ceramic metal housing and the post, the one the original Ody came with seemed to big.
It sort of squished out on tightening.
It sort of squished out on tightening.
@hera
take Ortmann wire double and your problem is forget
Ortmann Wire is sale from german flower vendor
Zubehoer und Preise fuer Kapillarbewaesserungsanlagen
number 102 is the wire
i take them for all A2, A1, Iatty and Odysseus
take Ortmann wire double and your problem is forget
Ortmann Wire is sale from german flower vendor
Zubehoer und Preise fuer Kapillarbewaesserungsanlagen
number 102 is the wire
i take them for all A2, A1, Iatty and Odysseus
Got my upgrade kit today along with the GGTS base. It's working great but on a couple of occasions after refilling I'm also getting juice dripping out of the centre pin. The only way I could stop it was to strip everything down and start from scratch, making sure everything is tight and in its correct place (o-ring specifically) and that seems to stop it. I'll try setting it up with another strand of wick if that's the solution.
One question: should the plastic window have an o-ring on either end? Mine only has one and I don't have anymore supplied that'll fit.
One question: should the plastic window have an o-ring on either end? Mine only has one and I don't have anymore supplied that'll fit.
I would think so Stalker.
I dont have my upgrade yet, but all the windows for the UFS's have an o-ring on both ends.
Someone must have missed one. It might not leak regardless, though.
I dont have my upgrade yet, but all the windows for the UFS's have an o-ring on both ends.
Someone must have missed one. It might not leak regardless, though.
The Stalker, did you not get the bag with 6 o-rings in it ?
I used the 2 biggest o-rings on the window.
I used the 2 biggest o-rings on the window.
I had the bag with the o-rings. Didn't count how many though. I put the two big ones on the GGTS base and the window. It's not leaking where there's no o-ring, but I've not tried laying it down yet.
@ the stalker open the juice control ( mouth piece) slightly before putting the 2 top caps on helps equalize the pressure been working for me at least
Cheers Rizz, I'll give that a try next time I re-fill.
My GGTS Ody base came with the o-ring on it.
Had mine laying down for an hour or two and no leaks, I also used 2 length's of wick and ran both down the side.
Had mine laying down for an hour or two and no leaks, I also used 2 length's of wick and ran both down the side.
Last edited:
how do i use oddy with 510 cartomizer? i can kind of work out with a punched carto but without a punched one would it work? do i put a drip tip on the end of the cartos?
Take one of the newer 4 slot wick ceramic cups from a Gotvapes Grande 5ml tank, use this in your Ody & iAtty with the 4 wick pattern, this is by far better then the standard Ceramic cup and doubling your wick or single wick, it produces guys and so do the Grande tanks but this will help make the Ody & iAtty wick and work much better.! you can also make the same 4 wick pattern and use this on your Ody and it will make the Ody work better even if you run 2 wicks through the 2 slits and the other 2 right over top and screw your mouth piece over it, or you can notch your ceramic and metal piece like I did, a high powered band saw worked wonders.
Last edited:
- Status
