Older Folks and Vaping Front Porch - Part Three

[Wolfenstark]

I write down on a piece of paper the builds in each atty I'm using , wire gauge, diameter, wraps, resistance, date of build.
Once the paper is full I toss it out and start a new one , don't keep historical records.

 

[Semiretired]

Hmmm, me - I wrap it - test it - vape it... One mild variance from one to the other - no problem... Just as long as I avoid a short...

 

[Robert Cromwell]

For me it is really simple. 6 wraps of 32 ga Kanthal on a 1/16 drill bit. All are the same.

 

[holimakaru]

I still introduce eGos to any possible v-vert.

Me too.
And I still use them for "stealth" vaping with a mini Davide or a 5S.

 

[Debadoo]

Howdy Holi......how ya been?

 

[DingerCPA]

Happy Belated, Miss Deb - sry - missed the party. Hope it was a glorious day

 

[Debadoo]

Happy Belated, Miss Deb - sry - missed the party. Hope it was a glorious day

Thanks sweetie! It was great, got tons of ECF birthday love

 

[Iffy]

OK, fer those that have been holding off on stocking up on PG/VG for TEOVAWKI, this is da be$te$t deal ever!
ESSENTIAL DEPOT - dat's 'round $0.006 per ml

 

[Debadoo]

OK, fer those that have been holding off on stocking up on PG/VG for TEOVAWKI, this is da be$te$t deal ever!
ESSENTIAL DEPOT - dat's 'round $0.003 per ml

That's fantastic even with the shipping

 

[Iffy]

That's fantastic even with the shipping

Truth be told, when I did a trial run, there was no shipping included. Went back and *poof* it was there. So, it's not da bestest deal, but close.

My bad...

 

[MagicJosh]

The front porch is great to vape at LOL but I like vaping in bed better. Man, those front porch vapors! They be on the look out yo!

 

[Debadoo]

Truth be told, when I did a trial run, there was no shipping included. Went back and *poof* it was there. So, it's not da bestest deal, but close.

My bad...

well dave had looked up the shipping some time back and even with that, it was still a good deal

 

[DavidOck]

Me too.
And I still use them for "stealth" vaping with a mini Davide or a 5S.

8 regulated tubes, 4 boxes - and a slew of spinner types. Although I tend to full size Davides and PT on those, yep, great for being less obvious, and great for a flavor change, or for when I just want something lighter in the hand. All the big stuff gets fitted with KFs and similar rebuildables, but if I'm going to drop something in the mower path, I'd rather it not be one of those!

The front porch is great to vape at LOL but I like vaping in bed better. Man, those front porch vapors! They be on the look out yo!

Howdy, and welcome!

Yeah, vaping in bed - something I NEVER did with smokes!

 

[Frenchfry1942]

Anyone else OCD about tracking their builds.

Topper Log as of 7/14/2015

R91 v1 - Pom - unused @ .93Ω, 5/30, Delasco
R91 v1#2 - JH - Provari - 1.7Ω, 2/24 Delasco
R91 v2 Nano - JH - iStick - 1.16Ω, 7/14 Delasco
R91 v2 Nano - POM - SS Workhorse - 1.16Ω, 5/30, Delasco
R91 2.0 - JH - Workhorse - 1.1Ω, 6/25, Delasco

KFL - Pom Uma @ 1.2Ω 4/21 (5/3 ok)
KFL oem - JH - rDNA @ .14Ω 5/16 KGD
KFL V4 - JH - Nemi @1.2Ω 6/1 Delasco
KFL V4 - Pom - SS Poldiac @1.1Ω 7/2 Delasco
KFL V4 oem - JH -Provari P3 @ 1.43 7/11Delasco

Taifun - POM - Provari-mini, 1.3 ohms, 2/16 Delasco
Taifun2 - Pom - WrkTele - 1.13Ω, 4/31 (or 3/31???)
"
Gkmf/Super-T - JH - 1.07 ohms(Mike), 2/16 Delasco

================================
ErlPrinz (new 5/29/15)

5/29
1st: 28g, 7x, 2.5mm @1.37Ω, Delasco
5/30 new coil
28g, 8x, 2.0mm @ 1.28 ,Delasco, JH

5/29
2nd: 28g, 7x, 2.0mm @1.01Ω, Delasco, POM
6/20, new Delasco

================================
Ego-One on eVic VT
7/10 - new .2Ω Nickel Coil

================================
Janet’s toppers
(temp: 6/21 - blue moved to pink stick)

Kayfun Nano - Janet- JH - iStick-pink 1.3Ω, 7/11
9/6 - new coil
28g, 9 wraps, 2mm @ 1.36 ohms, KGD
9/11 - new KGD
9/30 - new KGD
10/18, dry burn reused KGD
12/12, new KGD
2/1, new Delasco
2/28, new Delasco (lots of gunk, so spaced the coil)
3/28, new Delasco
4/21, new Delasco
5/14, new Delasco, iStick reading 1.5Ω30g, 7x spaced, 2mm, 1.7Ω
6/1, new Delasco, meter=1.45
6/19, new Delasco
7/11, new Delasco

Kayfun Nano - Janet- POM, Provari - 1.7Ω, 7/14
10/7 new coil / KGD
30g, 8x, 2mm, 1.9Ω
10/13 new KGD
11/1 new KGD
12/12 new KGD
1/12 new coil, Delasco
30g, 7x spaced, 2mm, 1.66Ω
2/1, new Delasco
2/28, new coil, Delasco
30g, 7x spaced, 2mm, 1.7Ω
3/30, new Delasco
4/20, new Delasco
5/3, new coil
30g, 7x spaced, 2mm, 1.68Ω, Delasco
6/1, new Delasco
6/19, new Delasco
6/25, new Delasco
7/9, new Delasco
7/14, new Delasco

KFL-Nano - Janet- BB, Mvp @ 1.46Ω, 7/9
3/20 - 1st coil
28g, 6x, 2.5mm, spaced, 1.12Ω
last used @ 1.12Ω 3/20 Delasco
4/8 coil ok, wick turning)
moved to Janet’s inventory - 5/24
5/24 new coil
28g, 8x, 2.5mm, spaced, 1.46Ω
6/1, new Delasco
7/9, new Delasco
Gs-Air (new 5/26)
================================
air-M - POM 5/26

air-MS - JH 5/26

================================
drippers
CTL-slv - JH 10 - .74Ω
10/7 - Dual coil, 28g, 10x, 2mm, .74Ωs
ea coil ~ 1.5Ω, 1cm KGD
12/5 - rebuilt w/ Nickel
3mm, 10wraps, twisted 32, .29Ω
12/7, 8 wraps, twisted now @ .21Ω

CTL-blk - POM 10 - .45Ω
10/7 - Dual coil, 28g, 6x, 2mm, .45Ωs
ea coil ~.1Ω, 1cm KGD

Sub#1 - Janet - JH
2/7 - std head,
30g, 5x, 2.5mm, 1.76 ohms, KGD

Sub#2 - Mike - Pom
2/8 - RBA head
30g, 6x?, 2mm, 1.56 ohms, KGD

================================

Taifun - POM - 1.3 ohms
28g, 2mm, 9 wraps spaced
8/9 wicked w/ KGD
8/10 re-wicked w/ more KGD was leaking
8/15 still flooding, re-wicked w/ KGD @ 10mm strip
8/16 - added some KGD at the ports to
Cut down on flooding out air hole
9/13 new KGD cut flush - no leaking so far (9/16)
11/18 new KGD
2/16, new Delasco

Taifun2 - Pom - WrkTele - 1.13Ω
4/31 - 28g, 2.5mm, 5x 1.13Ω <— 4/31 or 3/31???

KFL - Pom - Uma @ 1.2Ω
3/25 - 1st coil
28g, 6x, 2mm spaced, 1.2Ω
4/21, new Delasco
5/3, still looking good

KFL - JH - rDNA @ .14Ω
5/1 - 1st nickel build
28g nickel, 9x, 3mm @ .14Ω, KGD wick
5/16 - new KGD - lightly gunked, dark wick
(turned off temp, 2 light burns at 14 watts)

KFL V4 - JH - Nemi @1.2Ω
5/22 - new coil
28g, 6x, 2.5mm @1.2Ω Delasco
5/28 - new Delasco
6/1, new Delasco

KFL V4 - Pom - SS Poldiac @1.1Ω
7/2 - new coil
28g, 6x, 2.5mm @1.1Ω Delasco

KFL V4 oem - P3 - JH, @ 1.43 7/11Delasco
6/13 1st coil
28g, 7x, 2.5mm @ 1.43 Delasco
6/20, new Delasco
6/25, new Delasco
7/11, new Delasco

================================

R91 v1 - Pom - unused - @ .93Ω
XC-116 & 28g 7 wraps 3mm @ 1.5Ω
9/4 new coil 28g 8 wraps 1.5mm @ 1.0Ω
9/19 - new KGD wick
10/11, new KGD
Leaking
11/1 new Coil
28g, 7x spaced, 2mm, 1.07Ω, KGD
11/15 - still leaking, tightened block
Wick dis colored but coil not gunked - nice
New KGD wick
11/24, new KGD
12/1, new KGD
12/6, new Delasco
12/12, new Delasco
12/19 new coil
28g, 7x spaced, 2mm, 1.05Ω, Delasco
12/24, new Delasco, 1 piece, left some shoulder
1/12, as above, coil was black no gunk build up
(1/16, check coil, like new yet)
(1/19, coil still looking good, rebuilt anyway)
1/19 new wick & coil - Delasco
5x twisted 30g, spaced, 2.5mm @ .93Ω
2/16, new Delasco
2/24, new Delasco
3/15, new Delasco
4/23, new Delasco
5/6, new Delasco
5/30, new Delasco

R91 v1#2 - JH - Provari - 1.7ohms
8/20, 26g 6wraps 2mm .54 ohms KGD
10/13, 30g, 7x, 2mm, 1.7 ohms, KGD
10/8, new KGD
12/24, space the coil, new Delasco w/ shoulders
(9/1, coil is black but no gunk)
1/16, new Delasco
2/8, new Delasco
2/24, new Delasco (could use a new coil)
R91 v2 Nano - JH - iStick - 1.15Ω
6x 28g @ 1.2o 2.3mm (
7/3 - dry burn coil, torch wick
7/10 - dry burn to change flav
7/17 - dry burn, re-wick w/ melatonin
7/26 - new coil/wick
28g, 5 wraps, 2mm, .85 ohms, Melatonin
7/27 - bunked coil after 3 tanks
Used "just enough" for new wick
And cut 1/2 the ends off
7/28 - new CC wick, ~1/3 of rope
8/1, new CC wick, 1/2 old one was turning color
Coil had a little build up
8/7, coil had mild build up/wick was that funky color
re-wicked w/ KGD
8/12 - Dry Burn, new KGD wick
8/24 - new coil/wick
28g, 6 wraps, 2mm, ~.8 ohms
as much CC as I could, trimmed tails to point
8/25 re wicked w/ KGD, maybe too much CC
was getting burnt hits, 1 tank coil gunking but wick looked good
8/30 new KGD wick - dry hits with old one, tails maybe too thin
1cm not trimmed, was tight in 2mm coil
9/8 - new KGD
9/11 - new coil (old coil was actually 1.5mm)
28g, 7 wraps, 2mm, 1.06 ohms, KGD
9/21, new KGD
9/24, new KGD
9/30, new KKD
10/4, new KGD (early just because)
10/11, new KGD
10/18, new Delasco
10/26 new Delasco
10/29 new coil
28g, 7x, 1.06 ohms, KGD wick
11/7 new KGD
(1 dry hit - burn wick - duh!)
11/8 new KGD - bow tie, trim ≈½ tails
11/10 new KGD, full tails (was getting dry hits)
.... 11/19 new coil
Twisted 32g, 5 spaced wraps, 2mm, 1.15Ω
12/1, new KGD
1/9, new KGD (1/16, coil still clean)
2/14, new Delasco
3/6, new coil
28g, 5x, 2.5mm, 1.1Ω, Delasco
3/20 - new Delasco
4/9 - new Delasco
4/23 - new coil
28g, 2.5mm, 6x, 1.16Ω, Delasco
5/3, new Delasco
6/9, new Delasco
7/14, new Delasco
R91 v2 Nano - POM - SS Workhorse - 1.13Ω
4/9 - New coil, 8x 26g 2.5mm .9o
FD block, no side holes
6/3 new coil 7x 28g 2.3mm 1.3o
(2 wraps tape in post = 2.3mm)
(6x of 28g on 2.3mm = 1.14o
6/4 - cleaned, 7/3 new wick
7/6 - dry burn was tasting burnt
7/20 - dry burn, re-wick w/ Melatonin
7/23 - re-wicked
7/26 - new coil & melatonin wic
28g, 6 wraps, 2mm, 1.01 ohms
7/28 - new CC wick, ~1/3 of rope
8/1, very light coil build up, wick looked great
8/4, coil still looking decent, not much change
8/12, coil still decent
8/18 gunked bad, dry burn new KGD wick
8/22 new KGD 2x coil, wasn't bad but slight yuck taste
9/3 new coil & KGD 8+mm
28g 6 wraps @ .96 ohms
9/8 new KGD
9/21 new KGD
9/24 new KGD
9/30 new coil/wick
28g, 6x, 2mm, .96Ωs
10/4, new KGD (early just because)
10/8, new KGD
10/18, new Delasco
10/22, re-wicked Delasco,
Not leaking
10/29 new coil
28g, 7x, 1.08 ohms, KGD wick
11/7, new KGD
11/15, new KGD
11/24, new KGD
12/12, new Delasco
12/19, new Delasco 2x 20cm double insertion
12/24, new Delasco, 1 piece trimmed close to coil
12/30 New Coil
(7x, 28g, 2.5mm, 1.3Ω)
6x, 28g, spaced, 2.5mm, 1.13Ω, Delasco
1/16 coil still clean, re wicked Delasco,
2/9, new Delasco
2/23, new Delasco
3/21, new Delasco
4/8, new Delasco
4/20, new Delasco
5/3, new coil
28g, 6x, 2.5mm, 1.16Ω, Delasco
5/30, new Delasco
6/25, new Delasco

R91-2.0 - JH - Workhorse @ 1.16Ω
1/7 - 28g, 7x spaced, 2mm, 1.17, KGD
1/28, new Rayon
2/8, new Delasco
2/15, new Delasco
2/23, new Delasco
3/7 new coil
28g, 6x, 2.5mm, spaced, 1.1Ω, Delasco
3/22, new Delasco
4/10, new Delasco
4/21, new Delasco
5/30, new Delasco

================================

Gkmf/Super-T - JH - 1.07 ohms(Mike)
9x 26g w/ ReadyX
7/3 cleaned
8/3 re-wicked w/ CC ~1/2 width
Coil ID btw 2-2.5mm
8/9 new wick KGD
(Previous wick gunked just in the middle)
(Was OK for another day maybe)
8/18 - New KGD wick
8/27 - new coil / wick
28g. 6 open wraps, 2.5mm @ 1.07 ohms
9/3 new KGD @ 1cm
9/12 new KGD
1/9 rinsed clean w/ Everclear
2/16, dry burn, re-wicked w/ Delasco
just twisted and pushed it through w/ a pin - neat

Gkmf/Super-T - JH - 1.6Ω (Janet)
8/28 - 30g. 6 open wraps, 2.5mm @ 1.6Ωs, KGD
9/19 - new KGD wick. juice was dark but coil was fine

F20-350 - JH - 1.20hms
7/26, 28g 8 wraps, 2.5mm @1.2ohms, CC
8/1, coil needed cleaning, new CC wick
8/6, coil gunked on back, stretched coil, new CC wick
9/13 new KGD

F20-490 - Pom -1.1 ohms
8/10 28g, 7 wraps, 2mm, 1.1 ohms, KGD
8/14, new CC wick
9/12 new KGD
9/21 - adjusted post down for better batt contact

================================

ZAP - JH 2.0 ohms
8/13, 28g, 2mm, 10 wraps, 1.7 ohms, CC
9/6, 30g 6 open wraps 2.0 ohms KGD

iGo-#1 - 1.1Ω
8/8 28, 2mm, 8 wraps @1.1Ω
Rayon Wick

Go-#2 - .6Ω
8/12 26, 2mm, 6 wraps @ .6Ω
Rayon Wick

iGo- #1 & #2 rebuilt for DNA40
11/19:
2.5mm ID 12x NI200, 28g=.15Ω, 30g=.22Ω

iGo-Janet - shorty smoke - 1.56Ω
8/8 28g, 2mm, 9wraps @1.5Ω
Rayon Wick

Nautilus - JH
New 6/27, new 7/6, new 9/26 1.8 Bvc
II iClear - POM
New 6/29

DID - ??? - smoke tip - 1.0o
DID Temon - ??? - 1.0o
DID mini - ??? - 1.0o
Cobra - ??? - 1.5o
ZAP - Org/Virginia - 1.7o
5/22 cleaned


Davides
White Tip - Janet's Heaven,
Jan 6, Jan 25, Feb 5, Mar 1
Mar 24, Apr 11, May 5, Jun 2
Black Tip - pomegranate,
Jan 6, Jan 31, Mar 1, Mar 24,
Apr 11, May 4, , Jun 2
Chrome Smooth - Orange Dream
Feb 8, Mar 1
Chrome Groove - USA Blend
Mar 1

I keep a spreadsheet. Mostly to track when a topper got a new coil build. I track a lot of things though. My juice review tracking is pretty developed. Just part of the hobby. Life goes on.

 

[misswish1]

The front porch is great to vape at LOL but I like vaping in bed better. Man, those front porch vapors! They be on the look out yo!

Hi Josh, and welcome! These rockers are pretty comfy....

 

[Debadoo]

wow........susan is in the hangout and a fellow she follows who has a vape shop and advertises on Facebook got a notice from FB. this is some of what he said about it

Had a conversation with a representative of Facebook. Their policy is to not promote or support Vape or "tobacco related" products or pages/businesses. I was informed that within 3-6 mos. their updated algorithms will "SHUT DOWN" all such related pages. I informed them even the FDA has not of yet determined the correlation of vape and tobacco. Who the {Moderated}? are they to make that determination? Anyway, just a warning to anyone that has a vape related FB page or likes one, it will be gone shortly. I think everyone who does not want to see this happen should contact FB and let them know.

This is BS and burns me up! Don't know if this will affect private vape groups, but it sounds like it will to me

 

[3mg Meniere]

wow........susan is in the hangout and a fellow she follows who has a vape shop and advertises on Facebook got a notice from FB. this is some of what he said about it



This is BS and burns me up! Don't know if this will affect private vape groups, but it sounds like it will to me

It certainly does burn. I get FB notices from one vendor, and belong to another buy, sell, trade and pif group.

 

[MikeE3]

I keep a spreadsheet. Mostly to track when a topper got a new coil build. I track a lot of things though. My juice review tracking is pretty developed. Just part of the hobby. Life goes on.

ah ha! someone else.

 

[FlamingoTutu]

wow........susan is in the hangout and a fellow she follows who has a vape shop and advertises on Facebook got a notice from FB. this is some of what he said about it

This is BS and burns me up! Don't know if this will affect private vape groups, but it sounds like it will to me

There is a reason I never joined FB. This just moved to the front of the list. I suppose it's okay to plug Chantix and other stuff on there? I do hope FB users revolt and do it loudly.

 

[DingerCPA]

OK, fer those that have been holding off on stocking up on PG/VG for TEOVAWKI, this is da be$te$t deal ever!
ESSENTIAL DEPOT - dat's 'round $0.006 per ml

I scored on something similar a couple months ago (but I think there was a slight up-charge for the 1Gal of PG that I swapped. 4 Gal for $48 is INCREDIBLE, even if shipping is $20-30....