For rebuildables, I would recommend that you get a ReoMizer 2 (rm2). That is the easiest to rebuild. Note that a bottom feeder does not need tanks, the tank is built in.
-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
PDIB's Making MODs!
- Thread starter pdib
- Start date
- th_trl_thread_readers 0
- Status
For rebuildables, I would recommend that you get a ReoMizer 2 (rm2). That is the easiest to rebuild. Note that a bottom feeder does not need tanks, the tank is built in.
sucks with silica. i will have to get more braverer before i decided to rebuild it and try it with cotton. LOL
I keep trying to get to the RM2 on the reo mods site, but the page won't load :/ I will keep trying, but is the site usually so busy or is it down?
I don't know .. .. but you know to get the "LP" version, yes? Unless you plan to buy a standard REO as well; in which case you might want the "regular"one. The regular RM2 is milled to have a skinny bottom section (so as to fit int he REO's catch cup). The "LP" is unmilled and won't look so funny on a mod without a catchcup (like mine). If you were to get a REO later, you could always get a "low profile" version, and you'd be good to go.
I've recently taken to modifying $10 Triangle's into bottom feeders. The result is an unmilled "Rm2alike". I've done two so far; they work great...
Sounds interesting...Custom...have you posted on this yet? Pics?
or, you could say what looks "funny" to some etc… so for folks like me who don't always get it right, funny is fine… in other words they both work on the Dibby
Most of the standard operating procedures given years and years of distilling over in Reoville apply here…
*one exception (at the current time) being the high performance factor built in to this here street-safe race car.
Where do I find those again? I had the website in my phone until I had to reset it.
I have not. I've spent most of my time on ecf in reoville. I didn't want to post about it there out of respect for Rob. He's the one who figured out how to mod these things for bf. I just copied his genius.
Here's the thread I used to figure out what was going on inside the Rm2:
http://www.e-cigarette-forum.com/fo...2-full-atomizer-itself-rebuild-pic-heavy.html
The first one I converted took about an hour. The second one took 30 minutes or so. I think it could be done in as little as 15 to 20 minutes with more practice.
If you see them in stock, do it then. 2 times now I have went to get some about 5 hours after the back in stock email was sent and they were already out.
Custom-Classic. I had been wondering what all goes into modding the triangle. It would be a real treat if you were to share. I have a pretty good idea how I'd go about it; but it seems you are the expert now. If you're not comfortable with that, it's cool.
looks like I'm late to the party! 
good work dib's!! although it will be a while before I can afford one! what with all ive been spending already, if mrs eel catches me looking at pictures on here of your mods shes sure to poke my eyes out for good haha haa... ....unless... I can do a cheap option and float you over a few boxes of matches and some superglue to build me a block of wood also 
good work dib's!! although it will be a while before I can afford one! what with all ive been spending already, if mrs eel catches me looking at pictures on here of your mods shes sure to poke my eyes out for good haha haa... ....unless... I can do a cheap option and float you over a few boxes of matches and some superglue to build me a block of wood also
Last edited:
I'm pretty much at a loss with the bottom feeder attys, but I looked at some that I had and I see that I have many toppers with the center post drilled out:
Would these be bottom feeders?
The Eternity and the Killer is included in this list... there are more, but I could only hold a few to 'attempt' to show the hole.
Would these be bottom feeders?
The Eternity and the Killer is included in this list... there are more, but I could only hold a few to 'attempt' to show the hole.
i've read the Killer will work. I used an Eternity for a bit. it worked as long as i left it screwed in a little loose in order to get air. i didn't bother looking into drilling an airhole in the cap-- just bought more rm2s.
Peter, I have been on the notify list with Empire Mods for a couple of months to be notified when the triangle comes in. Maybe Rob bought them all out. I did find two on Ebay although they came from Isereal. I laughed because they also had the adaptor for the "dry herb" I just wanted one for dripping not using my Reo to test flavors when I diy and I like the ceramic base. I contacted the seller to see if he would be getting more in but he said no. They were $10 a piece on Ebay when I bought them. Just a FYI. They seem to be hard to get your hands on!
Go directly to the source:
Triangle
This one may work as well http://www.fasttech.com/products/0/10006867/1608300-mini-a7-rebuildable-dripping-atomizer
Triangle
This one may work as well http://www.fasttech.com/products/0/10006867/1608300-mini-a7-rebuildable-dripping-atomizer
Last edited:
You know what's sad? I have no idea what group I'm in...hey PDIBS what group am I in??? 
If you like slightly smaller chambers, like the Igo-S, this and this just need the center post drilled to work for bottom feed. O-rings may need to be replaced, air hole enlarged, YMMV.
Robs RM2 and Igo-S bottom feeders are pretty good value IMO. If I took an rba to a local machine shop for bf mods, beyond FUBARing it, they would probably charge me $80 or so for the privilege
Robs RM2 and Igo-S bottom feeders are pretty good value IMO. If I took an rba to a local machine shop for bf mods, beyond FUBARing it, they would probably charge me $80 or so for the privilege
- Status
Similar threads
