That's interesting that you are tasting the wire... I was just reading about titanium wire. It's supposed to be superior in terms of oxidization - could eliminate hot spots (for those who use mesh) and is supposed to lack any metallic taste. I may give it a try - I'll let you know what I find.I have 28, 30, 32 ga and that awful Kanthal D .05, I don't like the taste on the 28 either...
I seem to do badly with the thicker wires, my 30 works the best for me (and I even taste that). No amount of heating and carbon film helps the thicker wires much for me, and if I vape it a lot, I end up with sore spots on my tongue (which means I have to not use that atomizer for a while). Just made the neatest teeny microcoil out of 30 ga on a corsage pin for my A7 (in Microstick). WOW, did that turn out amazing!!!
I will try a twist wrap soon
PDIB's Making MODs!
- Thread starter pdib
- Start date
- th_trl_thread_readers 0
- Status
Here's what's under the hood
Supe, I'm sure you've been asked this before, but what size screws are you workin with on that there Cyclone? I'm gettin real tired of searching for that tiny little allen wrench at the bottom of my rebuild box.
Not sure yet - waiting on more information from another forum.
Links to screws? Here are 2 pretty good ones.
Dark Zero goes in to some detail about sizes and bulk QTY's here:
http://www.e-cigarette-forum.com/forum/reos-mods/441159-modded-my-grand-fit-two-batteries-2.html
If you just want to buy a few, Kidney puncher sells 10 packs in 2 different head sizes. Both fit RM2/Cyclone/Hornet and so on...
Stuff for Modders - Kidney Puncher
I've also got screws and washers at RC Hobby shops. Just look for the size M2X0.4. They were a great place to size up the right washers too when I was still rigging up my AGA-T2
Dark Zero goes in to some detail about sizes and bulk QTY's here:
http://www.e-cigarette-forum.com/forum/reos-mods/441159-modded-my-grand-fit-two-batteries-2.html
If you just want to buy a few, Kidney puncher sells 10 packs in 2 different head sizes. Both fit RM2/Cyclone/Hornet and so on...
Stuff for Modders - Kidney Puncher
I've also got screws and washers at RC Hobby shops. Just look for the size M2X0.4. They were a great place to size up the right washers too when I was still rigging up my AGA-T2
Last edited:
I have three RM2s and an extra pair of screws from Rob to boot. Why did I never think to try them on my Cyclone?
I'm desperate! I'm desperate!
Wait, what are we talking about?
Sent from my iPhone using Tapatalk
Wait, what are we talking about?
Sent from my iPhone using Tapatalk
Man, I am haunting the Reo site and considering getting a BFer crash course before my 5th run Dibi is ready :/
What's the size variation between a Reo mini and a Dibi?
What's the size variation between a Reo mini and a Dibi?
I'm desperate! I'm desperate!
Wait, what are we talking about?
Sent from my iPhone using Tapatalk
Well I just ordered a reo mini, olive drab, to hold me over till I get my dibby.
My first BF. I have a few drippers, immortalizer, I go w, mini squid, patriot. Is it east enough to dremel a channel in any of these?
I don't care for the igo w, immo won't work for BF. but the igo a or patriot should work decent right?
My first BF. I have a few drippers, immortalizer, I go w, mini squid, patriot. Is it east enough to dremel a channel in any of these?
I don't care for the igo w, immo won't work for BF. but the igo a or patriot should work decent right?
Cutting a channel is the easiest way by far. It's much easier than trying to drill stainless steel.
T
T
the immortalizer will work as a BF, vaping it right now on a reo but I think it's way to big for a mini
Seems to be a trend. I just got my grand last week. My advice, do it. It won't replace your desire for a dibi, just make it stronger.
- Status
Similar threads
