Erl mini on Pico... nice and stealthy!
The two latest squonkers to join the rotation...
Kayfun mini came in...so far so good! Was a little worried about over wicking (because I tend to do it) but I got about 10 tanks through her with no dry hits.
I just need to remember to close the juice flow control down before refilling! Literally every time I've refilled it, I've flooded it. Lol
Can you give a pic and description of your wicking? I'm getting some dry hits.
Mini blasphemy
how do you like them? I have always dripped, am thinking about getting a squonker before the FDA ban hammer hitsThe two latest squonkers to join the rotation...
"byCA", by Vape Systems, Belarus
Flavor, vapor, capacity, versatility, looks, ease-of-use: OMG
Flavor, vapor, capacity, versatility, looks, ease-of-use: OMG
THAT IS SOME SERIOUS FOG!!!"byCA", by Vape Systems, Belarus
View attachment 564907
View attachment 564909
View attachment 564911
View attachment 564915
View attachment 564917
View attachment 564921
View attachment 564923
Flavor, vapor, capacity, versatility, looks, ease-of-use: OMG
HeheDouble mini blasphemy if you catch my drift
That's a good looking quilt, at least it appears to be a handmade quilt.
Yes sir...I'll be trying out a new coil today or tomorrow, so I'll snap a few pics.
One thing that helped me was opening up the juice flow...I do almost three full rotations.
Q, what is it?!"byCA", by Vape Systems, Belarus
View attachment 564907
View attachment 564909
View attachment 564911
View attachment 564915
View attachment 564917
View attachment 564921
View attachment 564923
Flavor, vapor, capacity, versatility, looks, ease-of-use: OMG
Here ya go @ToolmanTexas
(Warning, I'm not good at giving instructions...if you have questions, ask away. Lol)
Shove some cotton in there....The typical "not too much, but not too little" I trim the wick so that the ends sit right above the holes in the well, but not touching.
Then I "bend" them down in the channels and fluff them out, using ceramic tweezers.
Like i said earlier, I open the juice flow 2.5 to 3 turns. 60vg/40pg juice.
1.2ish ohms, 12-18 watts. Flavorful goodness.
(Warning, I'm not good at giving instructions...if you have questions, ask away. Lol)
Shove some cotton in there....The typical "not too much, but not too little" I trim the wick so that the ends sit right above the holes in the well, but not touching.
Then I "bend" them down in the channels and fluff them out, using ceramic tweezers.
Like i said earlier, I open the juice flow 2.5 to 3 turns. 60vg/40pg juice.
1.2ish ohms, 12-18 watts. Flavorful goodness.
Here ya go @ToolmanTexas
(Warning, I'm not good at giving instructions...if you have questions, ask away. Lol)
Shove some cotton in there....The typical "not too much, but not too little" I trim the wick so that the ends sit right above the holes in the well, but not touching.
Then I "bend" them down in the channels and fluff them out, using ceramic tweezers.
Like i said earlier, I open the juice flow 2.5 to 3 turns. 60vg/40pg juice.
1.2ish ohms, 12-18 watts. Flavorful goodness.
Thanks a ton Ptech!... this is very close to what I have and honestly I was going good until I refilled and then dry hit city. My juice is OpenSourceVapor which is 100% VG but distilled down for tanks.
I'll try fluffing cotton a bit more and make sure I give at least 2 turns when refilling.
Similar threads
- Locked
