Post pictures of your working wick and coil setup

[AMDTrucking]

ok no worries, i cancelled it b efore i came back to see if i had a response, im sure you are right about the need of more heat with the size, it looks like it needs horizontal or close to horizontal builds running along they holes to make it hit nice rather than verts with the wick in the way/path of the airflow, hmm im kinda wishing i bought it now lol, was gonna get a hades to go with it but didnt realise untill i went back to cancel that it has the firebutton i dont like, i like the ones where you can sit the mod down without firing or adjusting before being able to ..........

Here I tried Horizontal Dual Parallel 28 Gauge at 0.3 Ohms.
A little better but not my favorite all day vape. Magma, however is.

 

[SLIPPY_EEL]

Here I tried Horizontal Dual Parallel 28 Gauge at 0.3 Ohms.
A little better but not my favorite all day vape. Magma, however is.

atleast you tried it, although personally i would have gone something like 24 or 22 so as to cut down on the amount of wire in the atty and try to get the ohms 0.15 or lower on they big batteries, which brings me onto another thing, i need to get some 26650's before my mod arrives, has anyone got any suggestion's? i was looking at the efest, then someone suggested the keeppower for super sub ohm but they dont seem to be the same chemistry, what to do what to do?

 

[Tbev]

Magma

0.8mm X 0.1mm A1 Kanthal flat ribbon NR-R-NR with Rayon 0.35 Ohm

@ TBev, You should definitely give this one a try if you are as flavor junky as you say you are.

22ga. At 0.35ohm , had this little guy for a while, I like it but I don't think it has dethroned the quasar in the flavor department. And it's so fugly. . .

 

[AMDTrucking]

22ga. At 0.35ohm , had this little guy for a while, I like it but I don't think it has dethroned the quasar in the flavor department. And it's so fugly. . .

This is just my opinion: What I'm looking at (picture above) is a "Vapor Junky" build, NOT "Flavor Junky" one.
I think if you change it to 26 Gauge to about 0.5 - 0.6 Ohms, you are going to re-discover your Magma all over again in a Flavor department. IMHO

 

[AMDTrucking]

22ga. At 0.35ohm , had this little guy for a while, I like it but I don't think it has dethroned the quasar in the flavor department. And it's so fugly. . .

Because you spoke highly about Quasar, I re-visited mine today. This one is made by ToBeCo:

Don't get me wrong. Quasar is not a bad RDA. But, IMO, Magma and Veritas are better.

 

[AMDTrucking]

UD IGO-W14

0.8mm X 0.1mm Flat Ribbon and Rayon 0.23 Ohm

 

[Tbev]

Yeah that's the first build I ever put on that magma, I was at my other house n all I had was 22ga I am running it at 0.5 0hm with 24ga and it's quite a bit better. I still like the quasar tho. But I run that at 0.4ohm with 24ga.

 

[TheKiwi]

Just for sheets and giggles.

View attachment 373880

View attachment 373881

Pardon the sloppy coils; I don't even dare to fire it to pinch the coils.

And no lol I didn't vape that.

 

[havok333]

Just for sheets and giggles.

View attachment 373880

View attachment 373881

Pardon the sloppy coils; I don't even dare to fire it to pinch the coils.

And no lol I didn't vape that.

What did it meter out to?

 

[TheKiwi]

What did it meter out to?

Right after I build it, it was 0.1

Decided to tighten the screws nice and snug, and it plunged down to 0.08.

Just wanna reiterate I didn't fire that thing up. Lol

 

[AMDTrucking]

I think I found a build for this three headed pitbull (Cerberus) that I can enjoy vaping.

0.8mm X 0.1mm Flat Ribbon and Rayon at 0.2 Ohms

 

[havok333]

Right after I build it, it was 0.1

Decided to tighten the screws nice and snug, and it plunged down to 0.08.

Just wanna reiterate I didn't fire that thing up. Lol

Smart man! Looks pretty cool though.

 

[AMDTrucking]

atleast you tried it, although personally i would have gone something like 24 or 22 so as to cut down on the amount of wire in the atty and try to get the ohms 0.15 or lower on they big batteries, which brings me onto another thing, i need to get some 26650's before my mod arrives, has anyone got any suggestion's? i was looking at the efest, then someone suggested the keeppower for super sub ohm but they dont seem to be the same chemistry, what to do what to do?

I like 26650 MNKE 4000mAH

 

[Tbev]

Can't wait till I can get an 18650 with 4 or 5k mah...

 

[Tbev]

I refuse to go 26xxx.

 

[havok333]

Can't wait till I can get an 18650 with 4 or 5k mah...

AND at least 35-45 amp continuous discharge!

 

[AMDTrucking]

Can't wait till I can get an 18650 with 4 or 5k mah...

Come on, get 26650 Mod already

You know, you want it

Big is beautiful. This one is only 10 Inches:

 

[Mikepresjr]

Run of the mill dual coil setup coming in at 0.6 ohms:

 

[Tbev]

Cut those tabs off brother!

 

[wonkeypickle]

I refuse to go 26xxx.

i second this. show me a battery that can beat my vtc, and i will. but until then, it's all sketchy batteries or discontinued old cells on ebay for 3x what they originally cost. The panny cgr is getting discontinued, no more sony vt, and an mnke battery will never come within 20 feet of my being, so that leaves those mods on the shelf for me. The icing on the cake is my tobh/stingray combo puts the 26650 setups i've tried to shame. pft.....