Post pictures of your working wick and coil setup

[USMCotaku]

What? No off set?

Nope... Used a fairly large diameter for a kayfun. It's working like a champ, no dry hits, great flavor, and even decent vapor amount for a kayfun

 

[USMCotaku]

Oh, I also made the top coil just a hair smaller then the bottom since its legs are longer, so they both heat up at the same rate
Sent with one hand, the other is busy vaping.

 

[Jjshbetz11]

This atty, on this box, with this mix of juice(cut with vg)
money....

 

[Jjshbetz11]

Seems like a nice cool vape!

Running quad coils on my RDAs.
28 awg A1 with 1.3mm id.
The Patriot is 7/8 wrap. Mutation X is 6/7 wrap.
Both come in at 0.26 ohm.

 

[iTiger]

Seems like a nice cool vape!

Thanks.
I learned a valuable lesson tho; the mutation hits harder and my pumpkin spice bars juice is a no no in it. Felt like my through was on fire.

 

[USMCotaku]

Thanks.
I learned a valuable lesson tho; the mutation hits harder and my pumpkin spice bars juice is a no no in it. Felt like my through was on fire.

Too high a Nic level?

 

[iTiger]

Its at 6 nic; I did go try it at 0 and was about the same. I think its the spice (mostly cinnamon I think) in it combine with the insane flow and better power transfer it has over the patriot.

 

[Jjshbetz11]

Cinnamon is a th killa, tend to stay away from cinnamon unless its done with a cream or frosting flavor

 

[iTiger]

Cinnamon is a th killa, tend to stay away from cinnamon unless its done with a cream or frosting flavor

That's the funny thing this juice has cream cheese icing flavor in it

 

[USMCotaku]

Just made a Clapton coil in my kayfun....

32 gauge wrapped around 28 gauge....6 wraps for 1.2 ohms. Kayfun has never worked so well
Sent with one hand, the other is busy vaping.

 

[DaveSignal]

stillare v3 clone. This setup is fantastic. Massive flavor and vapor. Its perfect with a wide-bore top cap. I just splash juice in there and it seems like it keeps going forever. Its a great rda.

 

[zipflint]

Amen on the Stillare V3. I love my clone. It has formed a long-lasting relationship with its matching copper Cartel.
Cartel and Stillare clones by zipflint, on Flickr

 

[nocigsnomore]

Kanthal A1 Wire 28g, 2mm, 8 wraps on the Goldpillar (Caterpillar II).

 

[AMDTrucking]

FT Squape R Clone with 30-30 (30AWG Ni200 twisted with 30AWG Kanthal) Rayon Wick.

 

[SLIPPY_EEL]

Fusion coil
0.13
3/32
2x24n + 32gA1
Really strong flavour & TH but not a hot vape

 

[Kevo333]

28g 4 strand nine wraps .3 ohm juice sucker lol

 

[1mouse3]

dual triple twisted 28g 3.57mm at 3.8 rap

 

[OthatGuy]

Finally got some good results out of my hobo dual twisted 28ga verts Netting 0.65ohm I had it at 0.25ohm and it ducked but my coils were just too small.

Not great pics but I'm pretty happy with it now.

 

[jonny45378]

Decided to build a parallel using different gauges. Went with a 22 gauge/ twisted 26 gauge parallel around a ~3 mm screwdriver and im using japanese cotton for the wicks. Came out to .22 ohms. Vapes great with a semi - fast ramp up time.

 

[SLIPPY_EEL]

YOyo Yo AMD TRUCKING..... the ribbon builds you are doing with the NR wire, is there a certain solder that is best for this? Thanks