How's that Ti wire working out for you? I don't think you have to space it out for TC to work properly with it but I could most likely be wrong
- Status
Im loving that build Tom, and the polished coils are hot to, i'm gonna have to try my hand and them all.
My Phenotype-L's came today, i flattened out some 18g A1 lastnight and it looked ideal for this atty.
1/8 id 0.15ohms and the vape exits the coil in the center and comes out on an angle just past the posts
tastes Vgood and i dont need to rejuice as often as im used to...
im appy my Tobh DT's fit this aswell..
My Phenotype-L's came today, i flattened out some 18g A1 lastnight and it looked ideal for this atty.
1/8 id 0.15ohms and the vape exits the coil in the center and comes out on an angle just past the posts
tastes Vgood and i dont need to rejuice as often as im used to...
im appy my Tobh DT's fit this aswell..
How are you liking it so far? The reason I chose against is because the airflow just seems massive & overkill to a point (unless your building something super hot just for cloud purposes). I'm rebuilding my Kennedy 24 today before I go build for other people, I'm either going to go quad 24/40g or 28/38g stagger fused with 40g. I have enough to make quads with the SFC but I would probably end up making duals with those. Suggestions?Im loving that build Tom, and the polished coils are hot to, i'm gonna have to try my hand and them all.
My Phenotype-L's came today, i flattened out some 18g A1 lastnight and it looked ideal for this atty.
1/8 id 0.15ohms and the vape exits the coil in the center and comes out on an angle just past the posts
tastes Vgood and i dont need to rejuice as often as im used to...
im appy my Tobh DT's fit this aswell..
@vapeNoob4 try making verticals, they may be easier to wick
Thanks. =) Still very much a noob at coil creation but am taking small steps onto masterdom. Lol. ...
Twisted 26g paralleled with 26g. Wrapped under tension on a 3/32 rod. .33 ohms at 80w on my istick 100w.
Atm Tom its my fav atty but i've only tried that one build you've seen above and it could just be down to having the coil centered under the DT that it tastes so bloody good, i do also have half of the airflow shut down.
i took a shot for you to see the size comparison up to the Velocity, there isnt a lot in it tbh when you take into consideration the velocity isnt as wide on the upper part, i also have the phen with the tobh Dt in the pic to show how much shorter that makes it but then you dont have airflow, i did try with airflow all open and is a little airy but taste was still there and clouds are good.
an advantage this atty is that the airflow doesnt impede on the deck as you see below..
no doubt i will tell you how it go's with dual in stnd position
i took a shot for you to see the size comparison up to the Velocity, there isnt a lot in it tbh when you take into consideration the velocity isnt as wide on the upper part, i also have the phen with the tobh Dt in the pic to show how much shorter that makes it but then you dont have airflow, i did try with airflow all open and is a little airy but taste was still there and clouds are good.
an advantage this atty is that the airflow doesnt impede on the deck as you see below..
no doubt i will tell you how it go's with dual in stnd position
Since it takes a Tobh's topcap, I'm going to make a wild assumption and say you may be able to fit a regular or comp cap from a vector on top as well. That would be pretty ridiculous and great at the same timeAtm Tom its my fav atty but i've only tried that one build you've seen above and it could just be down to having the coil centered under the DT that it tastes so bloody good, i do also have half of the airflow shut down.
i took a shot for you to see the size comparison up to the Velocity, there isnt a lot in it tbh when you take into consideration the velocity isnt as wide on the upper part, i also have the phen with the tobh Dt in the pic to show how much shorter that makes it but then you dont have airflow, i did try with airflow all open and is a little airy but taste was still there and clouds are good.
an advantage this atty is that the airflow doesnt impede on the deck as you see below..
no doubt i will tell you how it go's with dual in stnd position
This is the Sigelei 150w TC and Cigreen Triangle re-buildable.
Difficult to coil and wick due to the post design, but pulls like butter with my flavors. Currently dripping Northern Lights Bear Claw juice at 18mg. Coil setup resistance is 0.126 ohms.
Hi vapenoob, it looks like your wick isnt fully filling your coils, what happens when you fire it without the top cap on, i bet the wires glow.... you really need to fill the coils so as there are no gaps between the coil and wick but dont over do the wick so it is really tough to pull through...
Tom my Tobh barrel or the one from the Airek wouldnt fit onto the Phen-L but all chuffs and i have about 5 dif ones all fit onto the Phen-L's barrel & i dont have a vector to try for you
This would look sick as a stovetop. Been on a parallel gravedance kick lately.
26/38 fused clapton on a Pi2 (clone)
I'm really starting to like this attie
Much better to work with then ni. And no, you don't have to use spaced coils with ti, you can do contact coils just fine
Sent with one hand, the other is busy vaping
The pope in town has pushed my wire order into the unknown. 
Jealous looking at all the fun y'all are having. I'm DIY ing some juice instead.
Jealous looking at all the fun y'all are having. I'm DIY ing some juice instead.
the build i did earlier with the 5 wraps of 18g was 0.15ohms and is really tasty even with the air fully open, i tried a 0.1ohm dual of 4x 26g n80 twisted, same again fully open and it was to hot :/ tasty but hot! its confusing me cus ive been vaping dual aliens at 0.07ohms on the velocity's np's... weird or what
So I bummed enough some 36g to make a coil.
8 strand k1 ribbon / 26g ni80 frame / 36g ni80 fuse. Single coil hitting like a freight train. Wrapping the 8 pack of ribbon wasn't the funnest thing I've done. Clocking in at 1.9. Chock full o flavor.
I cannot stand when the wraps come loose. Makes my OCD kick into high gear.
8 strand k1 ribbon / 26g ni80 frame / 36g ni80 fuse. Single coil hitting like a freight train. Wrapping the 8 pack of ribbon wasn't the funnest thing I've done. Clocking in at 1.9. Chock full o flavor.
I cannot stand when the wraps come loose. Makes my OCD kick into high gear.
Hyon's got a $500 bounty in Hyon products for information on cloning factories & such.
26/38 fused clapton on a Pi2 (clone)
I'm really starting to like this attie
they made the pi2?
i noticed the pi2 was up for sale on ft for a very short while lol no loss to me, its not my cup of tea
- Status
Similar threads
