My problem may be an issue with air hole placement. I put the top cap on my Stillare on without paying attention to placement. Forgot that it mattered.
Sorry for the terrible quality of the pics.
Rayon wick, better flow, flavor, saturation and Nic Hit!
- Thread starter JeremyR
- Start date
- th_trl_thread_readers 0
- Status
My problem may be an issue with air hole placement. I put the top cap on my Stillare on without paying attention to placement. Forgot that it mattered.
Sorry for the terrible quality of the pics.
Nope. This is my third build (not counting an Ithaka with ready wire). I haven't tried to be creative yet.
Thanks for posting, the pics are good enough for me to see that you need more rayon, the wick needs to be thicker/ denser. You should have very slight shoulders showing full contact in the coil after break in.
Last edited:
try tilting the coils 30-40 degrees and have your wick spill onto deck. fluid has an easier path to coil.
ive got a quad that ive got both sets tilted and the wick looks like an ohms sign on each side
vapes nicely
Just so I don't go through every page of this thread again just to find it doesn't exist, did you post any pics of a properly wicked atty with this stuff?
On the Stillare, would you have the high point of the angle at the walls or at the center?
Took a long break from work to drive to Sally's beauty to get the regular CelluCotton 100% rayon. A lot easier to wick than the Tencel. Great flavor and vapor. Now let's just hope my newbie coil build is ok but so far way more flavor and vapor is good.
Are really dropping the ball as far as pics go on this thread... Post some pics already!
Sent from my Transformer TF101 using Tapatalk
Sent from my Transformer TF101 using Tapatalk
Here's a pic.. There are pics every couple pages.
Tight roll should help you get the right density.
With the wick rolled between palms and then thumbs it will then develop a set. You can roll it as tight as you want and it springs back. The wick is twice the size of the 1/16 I used to make the coil. This is the minimum it went in a protank with overwick.
I used a little more rayon in the dripper and with a bigger coil. here is a dry pic and a wet pic. I would say this wick was a little light here I could have easily used more wick.
Tight roll should help you get the right density.
With the wick rolled between palms and then thumbs it will then develop a set. You can roll it as tight as you want and it springs back. The wick is twice the size of the 1/16 I used to make the coil. This is the minimum it went in a protank with overwick.
I used a little more rayon in the dripper and with a bigger coil. here is a dry pic and a wet pic. I would say this wick was a little light here I could have easily used more wick.
How do you like that parallel build? Thanks for the pics!
Sent from my Transformer TF101 using Tapatalk
Sent from my Transformer TF101 using Tapatalk
It works.. I did parallel before i did twisted and I prefer parallel. Running on a zmax gotta keep it above 1.4 but with 32 gauge it gets hot and heats up fast. Usually run it at 15-24w with rayon. I ran 3 ohm for a long time in the past at 5-6v quick 3 second pulls with that, and long battery life.. Just recently started going parallel and twisted more since I'm stacking 350s I can push a full 6v to a 1.5 ohm coil for 24w and it heats hot and fast. And I can still get about 24 hrs on one set, easily twice as long as a single 18650. The parallel 32 is a lot stiffer than single strand and not springy like twisted. I also think its puts off better vapor with more wick coverage. With this build I'm taking 2-3 second pulls for clouds.
Thought I posted those but maybe not..
Problem is I don't have to rewick very often and I've been playing with the tencel lately.
Thought I posted those but maybe not..
Problem is I don't have to rewick very often and I've been playing with the tencel lately.
Just use a little more. It's only been a day you'll get it down very soon.
Also pulling on both ends of the rayon will even it out and shrink it so you can get same thickness on both sides. But you want to try to make it even to start with but if one side is really thick and the other side is too thin pulling it gently will reduce the bulge on the one side so you can pull even thickness to both sides.
Last edited:
I definitely missed this earlier.
You can't say this in my presence without more info. I'm a proud hardcore 5 pawns junkie.
Please share more info on this.
So I got good flavor for one or two draws this morning then back to poor flavor. I'm going to try cotton in this Stillare and see how that goes.
grandmaster ------- -------------- ----- gambit
lol!........peanut butter 6% ---- ---------- -- apple pie 8%
caramel 5% ----- --------- ---------- - french vanilla 5%
french vanilla 4% ------ -------- ----------- marshmallow 3%
banana creme 6% ------- ---------- --------- caramel 2%
------ ----------------------- --------- cotton candy 1%
hope you like them! enjoy!
Last edited:
i dont know about that...i use 80vg in mine...
i know i dont drip in the morning much...lungs arent broken in yet
i dont get why its different now....
all i can say is just look at it and see if anything changed
- Status
Similar threads
- Locked
