Rayon wick, better flow, flavor, saturation and Nic Hit!
- Thread starter JeremyR
- Start date
- th_trl_thread_readers 0
- Status
just chain vaped the taifun.......its the same...
still cant get a dry hit...flavor is great
still cant get a dry hit...flavor is great
I bought juice with a viscosity designed for tanks. Turns out it's designed for protanks. For my uses, I can't get it to work well in an RTA, but keep in mind I am inexperienced. When the flavor of this juice comes through it is amazing. Everything I could ever hope for from a 100% VG juice (thinned with distilled water). I definitely think I am tasting wick and think I will try thicker juice.
Some juices need more heat before the flavor comes out. Try cranking up the watts. I usually increase the power until the vape feels a little dry and harsh, then back off a bit.
Your venturing into a world that takes quite a bit of learning. Starting to build coils and sounds like your first dripper. I still think your tasting a dry burn at the coil that's not in contact with the wick. Or you have a hot spot.... What I thought was wick was actually the coil. Unless its tight as h... , Or you have a hot spot... I doubt its the wick your tasting.. That's my experience..
Please do try it with cotton, you'll see when it works good its in full contact with coil... Also your going from a tight Ithaka to a wide open super airy stillair. Close the AFC or take really sharp pulls.
Put 15-20 drops In There and see how it goes.
Please do try it with cotton, you'll see when it works good its in full contact with coil... Also your going from a tight Ithaka to a wide open super airy stillair. Close the AFC or take really sharp pulls.
Put 15-20 drops In There and see how it goes.
I think I will go to the building class at a local vape shop. Cotton isn't much better. I think you might be right about the coils.
i just had almost dry hit on one of the kf's...
turns out the chimney cap was leaking...its a cheap clear tank setup from slowtech.. changed the whole cap out and its great.
id be willing to bet that if that would have happened with cotton, it wouldnt have been an almost dry hit!
turns out the chimney cap was leaking...its a cheap clear tank setup from slowtech.. changed the whole cap out and its great.
id be willing to bet that if that would have happened with cotton, it wouldnt have been an almost dry hit!
this is all quite new....
i would suggest looking in beauty supply houses or googling "rayon balls". i dont know if sallys beauty supply ships to eu or not.
the stuff i like best is used in hair salons for when they do perms....
hope that helps
Yeah there's beauticians around the. World. You should be able to find a more local source... As a last resort if you can't find one you can contact local beauticians that do perms, inquire about it or ask where they get thier supplies... doctors also use rayon dressings maybe rayon balls
Wow - just read through this whole thread - I guess I'm a bit late to the party! You've got me convinced - off to Sally's today 
I'm hoping this solves the dry hit problems I'm having with my Fogger V4!
I'm hoping this solves the dry hit problems I'm having with my Fogger V4!
If you do a tight roll don't fit it too tight cause it actually will swell slightly. I like doing it loose but I have a lot of experience with it.
Caged you may want to try a higher ohm with higher gauge wire since your just starting out. Dry burn and see if they burn evenly. If your tasting the wick when you pull it out you'd see Scorching, not just staining from a gunked coil.
There's a ton of coil building threads on here that can help you greatly. Get you a good basic ground work, there's lots of videos out there too!
Last edited:
Wow - just read through this whole thread - I guess I'm a bit late to the party! You've got me convinced - off to Sally's today
I'm hoping this solves the dry hit problems I'm having with my Fogger V4!
ive got it in my fogger v4.3 and love it...got a .4ohm build with no dry hits at all with airband all the way out...no gurgling either
just pack a little more than you would with cotton and just cover the juice slots... i use a dentil pick to adjust it to sit on the juice holes
i do it to where its just getting to be snug...not tight.. as a test, i pull on a strand or two on the end and if its not too hard to pull through coil then its good...
i guess it just takes practise
The party has just started Amanda.. It's only taken off in the last two weeks and we've just this week secured suppliers and good experience with the tencel product. So your jumping in at just the right time.
Yeah your timing is good, a little bit sooner and you could have found yourself hunting the Internet for Alpaca fur!
Sent from my Transformer TF101 using Tapatalk
Sent from my Transformer TF101 using Tapatalk
I'll send you all the fur you want too! You just have to record yourself when you try it
On another note, I should have my rayon this week to try out.
On another note, I should have my rayon this week to try out.
- Status
Similar threads
- Locked
