SXK Doggystyle 2k18

[smoked25years]

My SXK 2k18 arrived, but I cant change the deck its so tight. I hear people can switch 2k16 airhole pin with 2k18. But after I screw 510 pin the deck is still tight like glued on the insulator. Any help here?

Remove the 510 screw and then use something (e.g. 2.5-3mm screwdriver or coiling rod) to gently push up on the post without pushing on the peek insulator. Be careful not to damage the post.

I wouldn't pry from the terminal side because you may damage the peek insulator underneath.

 

[AngeNZ]

Where else can this drips tip be found?
Prism T20S tank Drip Tip
I want some!

I searched the entire internet for them and only found them on that innokin site (which only ships to the states and is out of stock )

My only suggestion is to find an innokin replacement 20s tank somewhere cheap and get one that way.

Here's the fasttech link:
Innokin Prism T20-S Tank

 

[smoked25years]

A few months back I couldn't find the Innokin drip tips in stock. Several USA sellers have the Aspire Nautilus 2 drip tips but they are over priced. I ended up buying 3 of Nautilus 2 drip tips from Health Cabin for less than the price of 1 from a USA seller. I was expecting them to be shipped in an envelope but I received a huge box. Each drip tip was retail packaged and wrapped in a huge sheet of foam.

3 x Drip Tip for Aspire Nautilus 2 Tank Black - - (SZ0103032) $3.00
---------
Sub-Total: $3.00
Shipping Cost: $2.52
Discount Coupon: retailmenot : -$0.45
Your Final Payment: $5.07
Grand Total: $5.07

 

[AngeNZ]

The innokin drip tips don't work for jfc - so the aspire nautilus 2 drip tip would be the better option.

The innokin drip tips just aren't tight enough. Every other drip tip I've tried - including the nautilus fit tightly and adjust the jfc

 

[rifky]

Remove the 510 screw and then use something (e.g. 2.5-3mm screwdriver or coiling rod) to gently push up on the post without pushing on the peek insulator. Be careful not to damage the post.

I wouldn't pry from the terminal side because you may damage the peek insulator underneath.

Strange... it not budge at all. It seem glue to insulator. Maybe I have the first batch with black drip tip... Its really need a forced to push the pin out from the bottom?

 

[smoked25years]

Strange... it not budge at all. It seem glue to insulator. Maybe I have the first batch with black drip tip... Its really need a forced to push the pin out from the bottom?

I got the 2k18 and 2k16 topics mixed up. Sorry! I only have the '16.

 

[ricks]

I searched the entire internet for them and only found them on that innokin site (which only ships to the states and is out of stock )

My only suggestion is to find an innokin replacement 20s tank somewhere cheap and get one that way.

Here's the fasttech link:
Innokin Prism T20-S Tank

Thank you for trying! I tried looking too for a while and found nothing. Maybe they'll restock them??? I really like the shape of them.

 

[Dudeus Nordicus]

My SXK 2k18 arrived, but I cant change the deck its so tight. I hear people can switch 2k16 airhole pin with 2k18. But after I screw 510 pin the deck is still tight like glued on the insulator. Any help here?

The deck pieces came off without any effort on both the SXK 2k16 and 2k18 here. I had given both a customary regulation hot water rinse and wash though, even if it didn't appear necessary.

Perhaps a dip in hot water right before you attempt again would loosen it up?

Alternatively cooling the deck in the fridge or freezer might reduce the glueyness or shrink/solidify the insulator to same effect.

If the insulator still doesn't cooperate just consider using the 2k18 as is and give it another try later.

 

[rifky]

Found it.. It may a little tough to pull the airhole

 

[ricks]

The innokin drip tips don't work for jfc - so the aspire nautilus 2 drip tip would be the better option.

The innokin drip tips just aren't tight enough. Every other drip tip I've tried - including the nautilus fit tightly and adjust the jfc

You can change the orings on the drip tip to thicker ones to make it fit tighter.

 

[rifky]

Success changing airhole pin 2k16 and 2k18 by SXK

 

[stols001]

I just recoiled and rewicked a doggy in under 10 minutes. Personal best. Surely this means I can now bathe, gather up my stuff and GO HOME. I really need to get moving.

I thought I might do yoga. That is so off the table at the moment. I think it's going to be quite hard to take my trash out, actually. I probably should want to.

I KNOW it's the freaking Pneumonia but I am SO TIRED. Maybe I should nebulize and capitalize on the weird sort of shaky energy it gives you.

Also, the drive... It holds little appeal. I really can't ask the husband to gather up my needs for the week and bring them. Oh, I'd love to... but he has pneumonia TOO. Probably worse.

I'm SO tired but the doggy is vaping nicely. LOL. It kind of always does though, not so much of an achievement.

Ugh.

Anna

 

[AngeNZ]

Success changing airhole pin 2k16 and 2k18 by SXKView attachment 790171

What is your verdict on the 2k18?

 

[rifky]

What is your verdict on the 2k18?

To loose draw. Its a restricted direct lung, not MTL

 

[AngeNZ]

To loose draw. Its a restricted direct lung, not MTL

Yep, agree completely. Luckily for me that's my preferred vape.

But for mtl'ers who prefer the 1.8mm sxk 2k16 doggy it's a big difference

 

[ricks]

Strange... I'm getting good MTL with my 2K18. I have to close the air control 3/4 of the way tho. My 2K16, I leave 1/2 to fully open.