Tank-O-Matic Liquinator v4.1
- Thread starter Wylie
- Start date
- th_trl_thread_readers 0
- Status
Inner O Ring Size
Went through the thread with the search function and all I could find was the end cap size for the o rings, but had no luck finding the size for the inner oring which fits against the carto and gives the most problems since it gets cut by the slot with repeated use and filling.
I have had no problems with leaking with my 3 Liquinators over two months of use, but one of them just started to leak.
A temporary fix was to flip the Liquinator, but that one is showing signs to leaking as well.
I could order from Texas, but the postage for such a small item is more than the item which can be found locally.
Thanks
Went through the thread with the search function and all I could find was the end cap size for the o rings, but had no luck finding the size for the inner oring which fits against the carto and gives the most problems since it gets cut by the slot with repeated use and filling.
I have had no problems with leaking with my 3 Liquinators over two months of use, but one of them just started to leak.
A temporary fix was to flip the Liquinator, but that one is showing signs to leaking as well.
I could order from Texas, but the postage for such a small item is more than the item which can be found locally.
Thanks
So far so good. I only filled it half way. I had some gurgling issues that I think was from vaping too hard. I ordered some different syringes to make a couple more. I dont like the one I made today.
So how exactly can you fill the liquinator without removing the end caps? I've tried putting my finger over the hole on one end, while holding open end up I fill with liquid, then push the cart through. Are you guys doing something differently to fill yours without removing the end caps?
Sent from my ADR6400L using Tapatalk
Sent from my ADR6400L using Tapatalk
Just remove the drip tip, then slide the carto out from the bottom--just until you get a bit of daylight between the top of the carto and the top end cap. That's all the opening you need to squeeze your juice in. Easy peasey.
I'm looking for an XL length 3.0 ohm Boge carto to use with my 5 mL Liquinator on a VV box mod. Do these exisit?
I suppose, but you'd have to unscrew the whole works from your PV. I use Fushions, so I couldn't do it that way, anyway.
What don't you like about it?
You can get some 20ml syringes on the cheap on ebay. I ordered some today for .30 each, so .60 for a tank mod. I'm good with that.
You can get some 20ml syringes on the cheap on ebay. I ordered some today for .30 each, so .60 for a tank mod. I'm good with that.
Be careful not to puncture the center tube on the cartos or you will suck in juice,lol.
I paid just under 4 bucks for 4 20ml ones. Can you post where you ordered yours from?
Exactly how is this accomplished? I'd love to know how I can get this to work without sliding the slotted section through the orings
Sent from my ADR6400L using Tapatalk
The slot is at the bottom end of the LQ. Simply flip your LQ over with the carto in it, push the threaded side of the carto in until you see a gap, and refill. Just like James does in the video. It's simple.
Just forward to 1 minute and 30 seconds in the video:
Just forward to 1 minute and 30 seconds in the video:
Last edited:
I got them here on ebay. http://www.ebay.com/itm/290583956073?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649. I offered $15 for 2 packages of them, and the seller accepted. I figure I'll have plenty to play with, and I can always sell off the extras if I don't need them.
Last edited:
The last 5 packs of boge lrs have had loose threading, like it wobbles when almost fully seated. Something is up with the boge stock lately, I've been using them since i started 10 months ago and I'm having trouble finding one good carto in a 5 pack.
- Status
Similar threads
