TC beyond Ni200: Nickel Purity, Dicodes; Ti, SS, Resistherm NiFe30; Coefficient of Resistance

[dwcraig1]

He added it. On Steam Engine that is.

When I get to work I'll go there.
So I got to work and loaded the Invar 36 CSV from Steamengine and my Opus won't go into temp mode with it.?????

 

[JimScotty0]

I've transferred my Aromamizer to my Dicodes. Using in on a DNA200 with EScribe first to get an idea of things.
I have it set to TCR value of .0011, 110 in Dicodes speak.

Try setting it to .00117 which I was using or .00118 which is in the spreadsheet for the NILO 36.

 

[JimScotty0]

He added it. On Steam Engine that is.

That is awesome! Thank you @Dampmaskin!

 

[JimScotty0]

When I get to work I'll go there.
So I got to work and loaded the Invar 36 CSV from Steamengine and my Opus won't go into temp mode with it.?????

What was your build? Did you build it too low?

 

[dwcraig1]

What was your build? Did you build it too low?

0.25 ohm, two coils, 3 mm id, invar

 

[2legsshrt]

WooHoo my NiFe made it to Flushing NY. Hope it doesn't get flushed.

 

[2legsshrt]

@TheotherSteveS so was it you that suggested the 6 wraps? I take it that is a microcoil and you think it would be ok at 3mm. You think 8 would be too many. Just not sure where to start now that my wire is actually in the US should be here within the month.

 

[2legsshrt]

Well I've got 2 more SXM's coming so I will have 5, love em. Also considering one of those DNA200 the Reuleux or something like that when it comes out. The one that takes 3 18650's instead of those Lipos. Oh I also found out the new SX350-J V2 Chip will fit into the M's if they ever stop working if it is any better. Getting ready for Vapocolypse. They will take TC away when they pry it out of my cold dead mouth.

 

[TheotherSteveS]

@TheotherSteveS so was it you that suggested the 6 wraps? I take it that is a microcoil and you think it would be ok at 3mm. You think 8 would be too many. Just not sure where to start now that my wire is actually in the US should be here within the month.

Not sure if I did...what atty you using bud??

 

[jazzvaper]

@TheotherSteveS so was it you that suggested the 6 wraps? I take it that is a microcoil and you think it would be ok at 3mm. You think 8 would be too many. Just not sure where to start now that my wire is actually in the US should be here within the month.

Well, just for you @2legsshrt I did several builds on one of my kayfun 4's.

Where 7-wraps of 24awg works on the Lemo 2, when I get the screws down tight, 24 awg on the K4 is difficult, in part because I damaged my hand 'bout a month ago. Clipping the wire close enough to the post is still not a good option because of the strength required to bend the wire back to the post (avoiding a short with the congestion ring).

So, I tried 5 wraps of 26 awg getting into the range I was hoping for with 24 awg. Have a working coil at 0.18 but need to rebuild that one also.

This is precisely what I meant about being "scientific": trial & error 'til you come to a good result.

I recall you are doing 5-wraps of Ti but would suggest you go down from 3mm to 2.5mm, though that may not make a huge difference.

 

[WharfRat1976]

I have 316L from Unkamen and an ipv4s. I assume I should run it in Ti mode???

 

[Eric Auer]

I'm currently enjoying SS430 in all my adjustable TCR mods. Both my 350J mods have ~0.9 ohm slightly spaced single coils in TSV4's (with silica wick) and the Reliant is sporting a single contact 1.8ohm coil in a Lemo2 clone with cotton.

I patiently await a wire shipment from the EU.

I run SS430 as well, Works great. Love that I can toss it on any mod, TC or not.

I have it in a Kraken on a Cloupor Mini+, In TI mode. Works great.

Eric

 

[Eric Auer]

I have 316L from Unkamen and an ipv4s. I assume I should run it in Ti mode???

TI mode seems to be the way to go.

You just have to play with the temp settings to get it where you like it.

Eric

 

[2legsshrt]

Not sure if I did...what atty you using bud??

I am using Kanger STM's. Good air flow and easy placement with enough room for 6 or 8 wraps.

 

[TheotherSteveS]

I am using Kanger STM's. Good air flow and easy placement with enough room for 6 or 8 wraps.

I havent tried the 48 in the STM but 6 wraps of 26g on 2.5mm should see you right aroun 0.19ohm or so..Give it a try!

ps. I only have 25 and 27g!

 

[Eric Auer]

@vapealone

Awsome that SS430 is on Steamengine!

Eric

 

[vapealone]

@vapealone

Awsome that SS430 is on Steamengine!

Eric

Yes Eric, it is
However, it is not my fault
The credit should go to @Dampmaskin an/or the one(s) requested him adding it/provided code to him.

I have sent him code on other materials only that he has put in kindly. I am still thinking tho to send TFR data on 410/430 just for the fun of it.
It is just that their curves are almost linear but not regular making it hard to make my csv data uniform w/o loosing accuracy.
Not because we need uniform data pairs (different TFRs at same temp points for each materials) I just like it that way
And so far I have failed to accomplish it

 

[2legsshrt]

Well, just for you @2legsshrt I did several builds on one of my Kayfun 4's.

Where 7-wraps of 24awg works on the Lemo 2, when I get the screws down tight, 24 awg on the K4 is difficult, in part because I damaged my hand 'bout a month ago. Clipping the wire close enough to the post is still not a good option because of the strength required to bend the wire back to the post (avoiding a short with the congestion ring).

So, I tried 5 wraps of 26 awg getting into the range I was hoping for with 24 awg. Have a working coil at 0.18 but need to rebuild that one also.

This is precisely what I meant about being "scientific": trial & error 'til you come to a good result.

I recall you are doing 5-wraps of Ti but would suggest you go down from 3mm to 2.5mm, though that may not make a huge difference.

Yep you are right I am using 5 wrap 3mm with Crazy Wire comes in at .28ohms it has worked really well for me. Never get Dry coil or flooding but I do like the higher resistance of the CW compared to Unk at .26 talking Ti. Flavor is excellent and seems the coils last and the wicks about 2-3 weeks till I taste a little difference.

 

[2legsshrt]

I see on a lot of the polls the Kanger STM still with all the sub tanks out there comes in 1st or 2nd almost every time. I have had really good luck with them and all I use anymore.

 

[cigatron]

I see on a lot of the polls the Kanger STM still with all the sub tanks out there comes in 1st or 2nd almost every time. I have had really good luck with them and all I use anymore.

Welcome to the STmini "exclusively" club. All I use too and they're all three the original V1 RBA. In TC they hover around 32w and never dryhit or flood. They'll vape all the way up to 45w with the afc wide open if wicked correctly. 24g Ti, 6wrap, 2.78mm, slightly spaced coils are like magic in a STmini.