The ML has the setting and the Q will havenand the IPV5 will haveit so far that is all I know.My ML got it with the latest upgrade
WISMEC Reuleaux RX200 TC
- Thread starter USMCotaku
- Start date
- th_trl_thread_readers 0
- Status
From what I can make out from the flyer, it looks like a complete new tank but I can't see a 510 connector in the picture?? I guess time will tell.
The exploded view at the bottom?
That's the head, not an entire tank.
Going by the left of the middle pair, wondering if that looks like any existing head/RBA.
Or would fit in place of one.
I have more drippers than tanks. I haven't actually handled all that many factory heads.
That's the head, not an entire tank.
Going by the left of the middle pair, wondering if that looks like any existing head/RBA.
Or would fit in place of one.
I have more drippers than tanks. I haven't actually handled all that many factory heads.
This could be interestingThis is what they have said about them
Sent from my LG-V410 using Tapatalk
That charger is really cool. Nice work. Thanks for opening up the mod for us.After hearing about bad soldering, bad wires e. t. c., I took mine completely apart and did not discover anything terribly wrong. Just normal Chinese stuff: Hot glue, sticky tape, cheap wires and overheated soldering. I didn't do much. Just re-soldered wires on board and put it back together. But I did not have any of the problems, people are describing here, to beguin with.
I chose not to rely on RX200 balanced USB charging port and use my SKYRC B6AC V2 Charger with a little balance cradle I made for it. It's been working fine for me.
I vape my TI builds in power mode on my RX. Much better overall vape for me. No comparison.
I just built another spaced Ti coil & running in Ti mode or TCR @375 it's just meh. Running the same coil in power mode @32 watts though is WOW. Too bad I'm not real comfortable running Ti in power mode, maybe I'll build a twisted K1 build & stick with power mode at this point? My SMY Mini60 TC runs the same Ti build in the same tank MUCH better, as in the same as the RX in power mode. So it's either the TCR that's off in my RX200 settings or the RX just isn't liking my Ti build.
I've been wondering about base resistance for TC builds on the RX200. I typically build around .15-.25 for my TC builds but if according to the Wismec specs that the resistance can be from .05-1.5 ohms would I be better off building higher? How does everyone do a temp build on the RX? Do you shoot for a lower or higher number? My other TC mods seem to want a .15 build on Ni200 but I never thought about it if I build with Ti or SS.
Well try this I just did and I've heard that with the Jtech chips it seems to work well. Try Ti mode 500F. Titanium should never be vaped on power mode it is very dangerous. If you keep trying different things in TC mode you'll get a good vape. Mine is a single coil 26awg and I am vaping it in Ti mode at 490F and it's really good. Try tightening the atty a little more also. I've noticed with this RX that it makes a difference but is vaping good in Ti mode but you need to use a higher temp. I'm using 21w for a setting but even dry burning Ti in power can be dangerous if you don't know what you are doing let alone actually vaping it.
Actually I am getting a good warm vape at 470F 20W. Like I say I am using a single coild 26awg 5 wraps 3mm about but I see why the res jumped to .30 it is a .26coil so I will let it cool and try to get it to reset. It usually comes in around .27-.28 it's never right but you can work around that.
I've been getting a great vape all day with TCR set at 375, 30 watts @ 460 degrees. I was just thinking out loud about base resistance since it seems like there's some wiggle room there.
OK it reset to .28 as usual and I am getting a good vape at 490F 20w Ti mode. You know Ti doesn't vape like Kanthal it is less vapor and for me a lot more flavor. And yes 375 does work well also the higher you go on the TCR the lower you need to go on the temp. These boards seem to run a little lower then the YiHi by that I mean with my SX's on Ti mode or on 366 you get a good vape with Ti at 420F which is where it should be. I just play around with these till I get a vape I like but don't use power mode with Ti. If the coil gets too hot it produces TiO2 which is bad.
Just checked my TCR settings, I ran 375, 400 & 425. I moved around all morning until I settled in at 375. I also got the new atty message & it reset itself to .28 from .23, that additional.05 made all the difference in the world believe it or not.
Higher starting res provides more change and more accuracy for the mod to TC on.
The math bears this out. However...
We're slightly limited by available choices in wire and the space to fit the coil.
So are the MFGs.
So while we see factory SS all over the place from 0.2 to 0.5 or 0.6, Ni heads seems to have settled around 0.2 and Ti around 0.4.
But if you can fit a higher res coil... in theory, you should.
Yeah... somewhere around 900+F. We don't vape that hot.
But dry burning can. So care is needed there.
I can't say how well it works, but Ti is semi-self limiting in Power mode.
Especially on a Mech, it seems. Theoretically... it's safe.
Nickel on the other hand... I think the "nasties" issue there happens at a much lower temp.
Potentially within our usage range, or the very upper end at least.
Yep I've just read Ti, NI200 TC only SS TC or power, Kanthal and Nichrome power only. Oh aand NiFe TC possibly power don't know I made mine glow like kanthal when I used it once. I have 2 spools of it might have to try it again. Worked OK in TC with a contact coil.
NiFe is fully TC-able. But if I used it, I'd learn about dry burn safety with it first.
NiChrome is safe to TC, but with a TCR down around 0011 (JT Math), I don't know what Kanger is thinking with their new mods.
And I'll amend what I said about Ti. I really don't know how a regulated mod would handle it in power mode. On a mech, the rising res throttles the created power applied at the coil.
A reg mod, I think, would not make that adjustment.
Perhaps in VV mode, but not in VW. So that's a safety question mark.
I'd have to care about the topic to look into it, to be honest. I don't have any Ti.
NiChrome is safe to TC, but with a TCR down around 0011 (JT Math), I don't know what Kanger is thinking with their new mods.
And I'll amend what I said about Ti. I really don't know how a regulated mod would handle it in power mode. On a mech, the rising res throttles the created power applied at the coil.
A reg mod, I think, would not make that adjustment.
Perhaps in VV mode, but not in VW. So that's a safety question mark.
I'd have to care about the topic to look into it, to be honest. I don't have any Ti.
- Status
Similar threads
