Youde Goblin
- Thread starter dravell
- Start date
- th_trl_thread_readers 0
- Status
I have used it and I can tell you this it is a beast for a tank. My buddy runs his own B&M shop and got one for a sample but wouldn't sell it to me it after. It has better airflow than some of the RDA's out there. It chucks clouds like a dripper but the flavor is where it shines and it is due to the reduced size of the chamber. Only way to explain it is take the derringer RDA slam a tank on top of it with the post design of the Plume Veil and that is the Goblin by Youde a tank that doesn't mind 75 watts with a 0.3 build. It is awesome sauce multiplied by infinity by far the best tank available to date.
Just bought the last Goblin v1.1 (3ml and 4.2ml chimneys & tanks) from an online shop and eagerly waiting for it arrive hopefully before the weekend ! Had to sell my loyal Delta II to get this, but I hope I wont regret it 
Ok, so the 510 connector tightened up reduced the leaking, but didn't eliminate it. So I did a different build. This time it was 28 ga kanthal 6 wraps on a 2mm screwdriver for .6 ohms. And this time, I wicked with enough cotton to have a small amount going about halfway down each juice channel. Just a bit, not packed in there.
The leaking so far seems to have stopped, I've had it laid on its side for an hour now without leaking.
And the flavor really increased vs the 26 gauge 8 wrap on a 2mm screwdriver for .5 ohms. Vapor reduced a bit, but I like this one for a flavor build quite a bit.
The leaking so far seems to have stopped, I've had it laid on its side for an hour now without leaking.
And the flavor really increased vs the 26 gauge 8 wrap on a 2mm screwdriver for .5 ohms. Vapor reduced a bit, but I like this one for a flavor build quite a bit.
FINALLY back in stock, mine should be on my way soon. I bought a silverplay in the interim and it's decent, but i'm pumped to try the goblin finally
Anyone else's insulator melting?
I run somewhere in the 0.3 ohm range.
It's like a soft rubber, unlike the normal delrin insulators I've seen in the past.
The coils are as far from the insulators as I could get it.
I run somewhere in the 0.3 ohm range.
It's like a soft rubber, unlike the normal delrin insulators I've seen in the past.
The coils are as far from the insulators as I could get it.
Last edited:
So have they fixed the problem with the post screws being too short for anything less than 24 gauge?
Oh god, I hope it doesn't have insulator problems lol. I'm so over worrying that after my subtank mini rba experience. Care to show us your build?
From my understanding the Goblin revision should have better post screws. I had a few emails with Youde and they explained that retailers where the Goblin was purchased should be carrying the new screws. Although I think the post block could have been the issue. Before I bought new set screws from another online store I would have connection issues on the positive block, not the negative posts.
Since it got glossed over. My V1.2 captures 28 gauge without issue. Though it appears the 28 gauge gives more flavor, but less vapor in my goblin.
So again, yes they fixed the screws.
Got my Goblin V1.2 today, its easily my favorite tank. This thing puts out the vapor, and tastes great too! No leaking at all thus far, and the posts easily capture 28 gauge kanthal . The build deck is freaking tiny though!
I just got my goblin in, I assume it is V1 it came with two sized tanks and chimneys.
Build a seven wrap duo coil with 28ga 2mm, the wire captured just like it should no problems what so ever.I reduced the airflow a little, still huge clouds and now the flavor is very good to.
Build a seven wrap duo coil with 28ga 2mm, the wire captured just like it should no problems what so ever.I reduced the airflow a little, still huge clouds and now the flavor is very good to.
Theres some confusion on the various sites regarding the naming for sure. Mine also came with the 2 sized tanks and chimneys, so I am pretty sure we have the same version. It was labeled 2.0 on the site I ordered from, but Ive seen it labeled 1.1 and 1.2 as well
It's definitely the second version, whatever it's properly called if it came with two tank sections and chimneys.
Youde tech's facebook page called it the v1.2 so that's probably the right naming convention.
Youde tech's facebook page called it the v1.2 so that's probably the right naming convention.
Wow...I'm glad I found this thread.... Ordered a couple of the Goblins.
Thanks everyone for all the great information here......!
Thanks everyone for all the great information here......!
I bought mine right here Goblin V2 - Triangle Vape LLC and they list it as Goblin V2.
I'm going to buy a couple more of the goblin, I like that it is small and light and I don't have to drip to get the same benefits.
- Status
