Youde Goblin

[Wolfenstark]

I gather you've played around with the watts and air flow ?
I have the same build currently and its fine, I say fine because I'm using a DIY juice that I made in a hurry and only used it in here and not another device.

 

[jonnytwocoils]

I only have mechs but that should not be an issue I've done plenty of builds on other rta's and rdas sure it will just take some tweaking...just looking for some ideas. ..maybe wicking needs to be fine tuned? Open to suggestions

 

[Wolfenstark]

Mines good at 35w 4.1 v good at 30 watts 3.8v. any lower takes a while to get going and any higher starts to get rather warm.

 

[Wolfenstark]

This one does good , most people follow it.
https://www.youtube.com/watch?v=SOzZw8ppG-0&spfreload=10

 

[thx997303]

28 gauge at similar resistance gave me better flavor, but also warmed the vape up a bit more than I wanted. Plus it gave a bit less vapor. May be something to try.

 

[SheerLuckHolmes]

So I love this device don't get me wrong but I can't seem to get the flavor to a point that I'm happy with...I know that its possible but seems I'm missing something small or I don't know what I'm running dual 26g 8 wraps each about .55...if anyone has any builds they have been wowed by the flavor I'd love to hear it![emoji120]

I was just thinking the same thing. Just got my Golbin yesterday. Built it out last night dual 10 wraps microcoil 28g Kanthal. Came out 0.810 ohms vaping at 18 watts wide open air flow. Reading through this thread I just now closed the air flow down to half of wide open. Huge change in flavor and the direct lung inhale is still comfortable. Who knew?

 

[bentnectar]

Has anyone had problems with their goblin leaking through the air holes. I just filled mine a second ago and i was in my car and placed it so the air hole was angled down and all my juice leaked out. there is now a juicy mess all over my cup holder! has anyone had this issue and if so any recommendations on how to fix this?

 

[JoeVan]

Mines good at 35w 4.1 v good at 30 watts 3.8v. any lower takes a while to get going and any higher starts to get rather warm.

35 watts seems to be the sweet spot for this device. That's what I have had mine set on for a couple weeks now.

 

[JoeVan]

Has anyone had problems with their goblin leaking through the air holes. I just filled mine a second ago and i was in my car and placed it so the air hole was angled down and all my juice leaked out. there is now a juicy mess all over my cup holder! has anyone had this issue and if so any recommendations on how to fix this?

This happens when you don't have enough wick in the channels. Put a little more wick in there, and you can set this sucker on it's side without a leak. I had this happen to me, too. Re-wicked and all was good to go.

 

[bentnectar]

This happens when you don't have enough wick in the channels. Put a little more wick in there, and you can set this sucker on it's side without a leak. I had this happen to me, too. Re-wicked and all was good to go.

Thanks i wil have to try this after i clean my cup holder lol..

 

[spawn]

35 watts seems to be the sweet spot for this device. That's what I have had mine set on for a couple weeks now.

I have a. 43 ohm build with 26 awg. Running at 41w. That's the sweet spot for me in terms of flavour and vapor. It all comes down the build, surface area and wicking.

To the guy having issues with flavour: if you put too much power through it you make lose the flavour so turn it down a bit and or check your wicking. If it's too dry you will also lose flavour.

Sent from my Nexus 5 using Tapatalk

 

[beez0527]

I got my goblin yesterday and after a night of soaking and a good scrubbing my first build came out perfect. This thing hits like a champ great flavor and airflow and no leaks what more could you ask for. I had always shied away from rta's as they were a pain in the ... and always leaked and airflow too tight but this i can tell is going to become my main tank.

 

[Wolfenstark]

Going good on a 26g 2mm 5.5w 0.3Ω build.

 

[tc1]

So noone else noticed if their air flow holes are slightly off on one side by a mm or two?

 

[Wolfenstark]

So noone else noticed if their air flow holes are slightly off on one side by a mm or two?

Ok just looked at mine - One side did 1mm open other side was 1mm. 2mm other side 2mm, 3mm other side 3mm. Fully open both sides fully open.

 

[jonnytwocoils]

Yep mine are perfect too

 

[inspects]

I'll be one happy camper when my bigger tank and chimney arrive........

Need more juice.......

 

[tc1]

Must be a quality control issue then. Not a huge deal to me, was just wondering.

 

[beez0527]

Mine is lined up perfectly as well my is the one with both tanks and chimneys.

 

[thx997303]

Both of my goblins, v1 and v1.2 line up perfectly.