Authentic Svoemesto Kayfun 5

[Robino1]

Okay.

Reporting back.

First pass through the range of juices I bought fromm HHV, and this is the first time (ordering juice from a new-to-me company) I can say that not a single one was a miss.

Wow. Good stuff. All of them.

That's spooky.

I would say Legend is one of the best baccy vapes I've ever had, but the truth is all of the baccy vapes I have here from HHV fall into that catagory. Really excellent.

And the fruits were all uniformly excellent as well.

That's got to be some sort of record, or astronomical event, or something.

Amazing and they can only get even better with a little age on them.

Thanks for the recommendations people.

Really amazed.

We need to do a drive-by on the FDA.

This stuff cannot be allowed to die.

That is why HHV is my only liquid vendor that I order from

After finding Dragon's Fire, that has been my only for almost two years now? I think it has been that long that it has been my only vape.

 

[Mike Geaney]

No leaks on the KF5 after my rebuild yesterday. I ripped the base apart, cleaned, re-lubed the O-rings, and re-assembled paying special attention to ensure the hex screw was properly tightened. Much better. Dry on the bottom as it should be.

 

[jwbnyc]

What tool are you using on that hex?

 

[Mike Geaney]

What tool are you using on that hex?

Had a small nut driver in my tool set that did the trick. Size escapes me and I'm not home ATM.

 

[Bronze]

What tool are you using on that hex?

The KM3 is a 5mm. Not sure if the K5 has the same size.

 

[Mada]

I have been using the K5 for several days now. I tried the stock air hole and the MTL kit. I didn't like both of them. They are good but not perfect for me. Then I made my own solution to make the air hole 2mm. It is perfect for me this way. But my biggest challenge is leaking. I don't have any leaking from KF4, KF mini v3 or even the GEM. But K5 leaks. I have been trying different solutions including cleaning and tightening the hex and the wicking method. But until now it leaks. It is very hot these days in Egypt, but other tanks doesn't leak. I will continue trying , may be I will find the solution and report it back.
Btw, I only got the steamtuners tank, it looks very good, much better than the stock. But it is not easy to fill as the stock design.

 

[Bronze]

I have been using the K5 for several days now. I tried the stock air hole and the MTL kit. I didn't like both of them. They are good but not perfect for me. Then I made my own solution to make the air hole 2mm. It is perfect for me this way. But my biggest challenge is leaking. I don't have any leaking from KF4, KF mini v3 or even the GEM. But K5 leaks. I have been trying different solutions including cleaning and tightening the hex and the wicking method. But until now it leaks. It is very hot these days in Egypt, but other tanks doesn't leak. I will continue trying , may be I will find the solution and report it back.
Btw, I only got the steamtuners tank, it looks very good, much better than the stock. But it is not easy to fill as the stock design.

Try Mike's approach. He completely disassembled and reassembled. See his posts above.

 

[Mada]

I already did that once, but I will try it again tomorrow.

 

[Mada]

Btw, I have two KF5 and both of them leaks but only when in a horizontal position.

 

[VapinBlues]

I have two K5, the GF is using one, and they both have condensation on the bottom after a day or two of use. I wouldn't call it leaking, but it does get a little wet down there. I think it has something to do with temp change, like going in and out of the office, hot and cold... but no way to test that theory.

I still use the K3 most of the day and that tank stays dry!

 

[AstroTurf]

The KM3 is a 5mm. Not sure if the K5 has the same size.

Yes, They both use 5mm socket.

 

[stanleybb50]

Still no place to buy this MTL kit I see..

Sent from my SM-N920V using Tapatalk

 

[Bronze]

Still no place to buy this MTL kit I see..

Sent from my SM-N920V using Tapatalk

Did you write Svoemesto yet?

 

[stanleybb50]

Did you write Svoemesto yet?

No.. I'll do that now.

Mine too has been shelved until I get that.

Still also waiting in a poly tank from Steam Tuners that just replaces the glass, to keep the capacity... I don't want the tower tank and reducing the 4ml capacity!

Sent from my SM-N920V using Tapatalk

 

[Bronze]

No.. I'll do that now.

Mine too has been shelved until I get that.

Still also waiting in a poly tank from Steam Tuners that just replaces the glass, to keep the capacity... I don't want the tower tank and reducing the 4ml capacity!

Sent from my SM-N920V using Tapatalk

I was civil when I wrote Svoemesto but I didn't hide my displeasure with them either.

 

[stanleybb50]

I just wrote. I was very civil.

Sent from my SM-N920V using Tapatalk

 

[Bronze]

I just wrote. I was very civil.

Sent from my SM-N920V using Tapatalk

Not as fun as being uncivil is it?

 

[angah83]

I have been using the K5 for several days now. I tried the stock air hole and the MTL kit. I didn't like both of them. They are good but not perfect for me. Then I made my own solution to make the air hole 2mm. It is perfect for me this way. But my biggest challenge is leaking. I don't have any leaking from KF4, KF mini v3 or even the GEM. But K5 leaks. I have been trying different solutions including cleaning and tightening the hex and the wicking method. But until now it leaks. It is very hot these days in Egypt, but other tanks doesn't leak. I will continue trying , may be I will find the solution and report it back.
Btw, I only got the steamtuners tank, it looks very good, much better than the stock. But it is not easy to fill as the stock design.

Hi Mada.. mind to share your own solution to make the air hole 2mm? Thanks!

 

[Mada]

I used a 2mm blunt needle tip. I cut it short to match the length of the MTL kit. Then I wrapped in Mesh to fit snug in the air hole.

 

[angah83]

Fixing Kayfun 5 airy draw my way..

Remember those three little metal? It's from a lagendary tank Vivi Nova.

I pick the one on the right. The inner diameter is 2mm. But the outer diameter is over 3mm which will not fit into the Kayfun 5 air channel.

I then take my vise. Use a nail to hold and secure it in place.

Using diamond file, start filing and inspect if it fit the air channel. If not, keep filing.. Once perfect..

Fixing Kayfun 5 airy draw my way.. From stock 3mm to 2mm.. I'm more than happy now!