Factors on a RTA that decide over taste?

[Zazie]

fasttech sells many different Dvarws . How do I figure out which one to get?

 

[Letitia]

fasttech sells many different Dvarws . How do I figure out which one to get?

If you want dl 24mm this one.
https://www.fasttech.com/product/9654669

Believe @Heartsdelight has ordered the 22mm mtl but I don't which one. I like the dl I have but it is a pretty loose draw.

 

[Janusz]

I've always liked that type of wicking because it made sense to me that the shorter the tails, the shorter the distance of travel. And especially if the tails are horizontal to the coil like a Hurricane deck.

Or like Kayfun... Dvarw...Reaper...


or Hussar............... Hussar is extremelly easy to build with 2.5mm coil and the same diameter rod I can secure coil perfectly centered and at perfect height in matter of seconds... you just place rod in those outside deck "U" shaped notches... position coil in center press it with thumb and secure legs with screwdriver in other hand. No hassle with trying it to center or adjusting height after securing coil legs.

Wicking is also very easy... cut it to edge of deck place it into wells fluff it and if necessary trim it so cotton will be even with top flat surface of deck (on this flat surface will rest bottom of tank so too much cotton would be compressed too much) wicking holes inside tank will be not on side but above those two wells so juice will enter coil from above and only through two inside wide "U" shaped openings. No worries about cotton in threads... press with little twist and turn middle translucent part to open juice flow...

It is very simple tank without dozen "O" rings and parts but at the same time most different tank from the rest of tanks I own and flavor and draw is superb... the only thing I do not like is small juice capacity but I plan to buy extension for it .

 

[Zazie]

If you want dl 24mm this one.
https://www.fasttech.com/product/9654669

Believe @Heartsdelight has ordered the 22mm mtl but I don't which one. I like the dl I have but it is a pretty loose draw.

The thing is, aside from the size differences (and there are 5ml jobbies called MTL), there are plain old Dvarws, V2 Dvarws, and V3 Dvarws. Some are described as "styled" and some not (with little price difference). There are Dvarws, ST Dvarws, YFTK Dvarws, Ulton Dvarws, and Coppervape Dvarws (none are labeled "authentic"). How to choose among them?

 

[Heartsdelight]

Fasttech sells many different Dvarws . How do I figure out which one to get?

Fasttech told me the Dvarw’s will no longer have logos if that matters to you. The 1st one Dvarw DL I got in January had a logo. The 2nd one I got a few weeks ago doesn’t. Same SKU. I ordered a Dvarw DL from 2fdeal & received in 7 days. If you want the sku I can give it to you.

Edit: the Dvarw DL from 2fdeal has a logo.

 

[Heartsdelight]

If you want dl 24mm this one.
https://www.fasttech.com/product/9654669

Believe @Heartsdelight has ordered the 22mm mtl but I don't which one. I like the dl I have but it is a pretty loose draw.

I’m thinking of getting the Dvarw MTL for my incoming Provari Mini but I didn’t order it yet.

 

[Heartsdelight]

The thing is, aside from the size differences (and there are 5ml jobbies called MTL), there are plain old Dvarws, V2 Dvarws, and V3 Dvarws. Some are described as "styled" and some not (with little price difference). There are Dvarws, ST Dvarws, YFTK Dvarws, Ulton Dvarws, and Coppervape Dvarws (none are labeled "authentic"). How to choose among them?

That’s how I felt looking at the Doggy rta. I asked on the SXK Doggy Thread. There’s so many it’s confusing. Also for the Provari Mini.

 

[Janusz]

The thing is, aside from the size differences (and there are 5ml jobbies called MTL), there are plain old Dvarws, V2 Dvarws, and V3 Dvarws. Some are described as "styled" and some not (with little price difference). There are Dvarws, ST Dvarws, YFTK Dvarws, Ulton Dvarws, and Coppervape Dvarws (none are labeled "authentic"). How to choose among them?

All Dvarws from Fastech are clones. Authentics are very expensive.

First decide if you want DL or MTL. V2 means newer version (can be top filled) of MTL and V3 is newer version of DL
If you decide for MTL you have to decide size 22mm diameter or 16mm diameter. After that decide if you want acrylic tank (whitish color PC) or ultem PEI yellow color. I do not remember what I bought but it was either Coppervape or YFTK... those are the most popular clone brands for Dvarw.

I wish to buy V2 but before I buy I would like to know if I can buy bigger air flow insert (2.5mm) or if I can use insert from my old Dvarw... anyone know???

 

[Heartsdelight]

All Dvarws from Fastech are clones. Authentics are very expensive.

First decide if you want DL or MTL. V2 means newer version (can be top filled) of MTL and V3 is newer version of DL
If you decide for MTL you have to decide size 22mm diameter or 16mm diameter. After that decide if you want acrylic tank (whitish color PC) or ultem PEI yellow color. I do not remember what I bought but it was either Coppervape or YFTK... those are the most popular clone brands for Dvarw.

I wish to buy V2 but before I buy I would like to know if I can buy bigger air flow insert (2.5mm) or if I can use insert from my old Dvarw... anyone know???

I think you can use the inserts. But I’m not positive. They sell with & without the additional inserts & the inserts can be purchased separately, I’ve seen them on FT.

 

[Heartsdelight]

@Zazie this one is rated really high on FT. 54 reviews. Comes with the airflow inserts. No logo. I’m going to get one to try.
https://www.fasttech.com/products/9652193

One of the reviews stated the 23mm Merlin’s glass tank fits.

 

[Zazie]

Thank you, @Heartsdelight (and you, @Janusz, for your very informative post). This one looks good, too: 88 reviews. 4.9 stars, and three different tank sizes.

 

[muth]

The thing is, aside from the size differences (and there are 5ml jobbies called MTL), there are plain old Dvarws, V2 Dvarws, and V3 Dvarws. Some are described as "styled" and some not (with little price difference). There are Dvarws, ST Dvarws, YFTK Dvarws, Ulton Dvarws, and Coppervape Dvarws (none are labeled "authentic"). How to choose among them?

Lol

 

[muth]

Or like Kayfun... Dvarw...Reaper...


or Hussar............... Hussar is extremelly easy to build with 2.5mm coil and the same diameter rod I can secure coil perfectly centered and at perfect height in matter of seconds... you just place rod in those outside deck "U" shaped notches... position coil in center press it with thumb and secure legs with screwdriver in other hand. No hassle with trying it to center or adjusting height after securing coil legs.

Wicking is also very easy... cut it to edge of deck place it into wells fluff it and if necessary trim it so cotton will be even with top flat surface of deck (on this flat surface will rest bottom of tank so too much cotton would be compressed too much) wicking holes inside tank will be not on side but above those two wells so juice will enter coil from above and only through two inside wide "U" shaped openings. No worries about cotton in threads... press with little twist and turn middle translucent part to open juice flow...

It is very simple tank without dozen "O" rings and parts but at the same time most different tank from the rest of tanks I own and flavor and draw is superb... the only thing I do not like is small juice capacity but I plan to buy extension for it .

So lucky there's an extension. I have little faith there will be one for the Zeta. There's not much promotion in the states or on YT for that one but my friend and I are enjoying it. I guess we're in a small club.

 

[Letitia]

So lucky there's an extension. I have little faith there will be one for the Zeta. There's not much promotion in the states or on YT for that one but my friend and I are enjoying it. I guess we're in a small club.

I suspect many good products get overlooked with something new being released almost daily .

 

[muth]

@Zazie Idk about Dvarw but Ulton is a damn good cloner. They are the original factory that made clones for SXK.

 

[muth]

I suspect many good products get overlooked with something new being released almost daily .

Good point. And the two English speaking vids for the Zeta are pathetic. No, worse than that....ill informed.

 

[AngeNZ]

Thank you, @Heartsdelight (and you, @Janusz, for your very informative post). This one looks good, too: 88 reviews. 4.9 stars, and three different tank sizes.

If you haven't clicked the order button - this one got recommended to me as it has all 3 tank sizes, airflow inserts and a stainless steel tank:
Dvarw MTL V2 Styled RTA Rebuildable Tank Atomizer

 

[muth]

All Dvarws from Fastech are clones. Authentics are very expensive.

First decide if you want DL or MTL. V2 means newer version (can be top filled) of MTL and V3 is newer version of DL
If you decide for MTL you have to decide size 22mm diameter or 16mm diameter. After that decide if you want acrylic tank (whitish color PC) or ultem PEI yellow color. I do not remember what I bought but it was either Coppervape or YFTK... those are the most popular clone brands for Dvarw.

I wish to buy V2 but before I buy I would like to know if I can buy bigger air flow insert (2.5mm) or if I can use insert from my old Dvarw... anyone know???

Have you scoped out the V2 on FT? Have a link or sku?

 

[Zazie]

If you haven't clicked the order button - this one got recommended to me as it has all 3 tank sizes, airflow inserts and a stainless steel tank:
Dvarw MTL V2 Styled RTA Rebuildable Tank Atomizer

Same link as the one I posted--I guess I guessed well!

 

[muth]

Same link as the one I posted--I guess I guessed well!

Do you know anyone who has the top fill kit? Wondering if it's worth it.