GP Series by VapourArt - Official Thread for GP Heron
- Thread starter perseas
- Start date
- th_trl_thread_readers 0
- Status
You might need to make the loops smaller , but yeah that will work great. I'm putting new wick in mine tonight , I'll post some pictures. That being said you'll figure it out easily enough.
Here I built with loops. Adjusted them when complete to mate with fluff without excess.Do you guys think these builds will work well on the heron? I don't have it yet but I'm so excited to get it i wanted to have everything ready to go haha, let me know what you think
http://www.e-cigarette-forum.com/fo...ips-tricks-updates-thread-3.html#post12391829
EDIT - Not sure what gauge wire you have there but appears your ohms will be in the mid to high twos.
1.5 to 2.0 seems to be ideal flavor and vapor range.
Make sure your tails extend from the bottom of the wick as they will be much easier to install and adjust. Good luck.
Last edited:
Do you guys think these builds will work well on the heron? I don't have it yet but I'm so excited to get it i wanted to have everything ready to go haha, let me know what you think
Hmm, I think you may have to make them a tad smaller and they will be fine
Hmm, I think you may have to make them a tad smaller and they will be fine
They are pretty small... a tad larger then the diameter of my finger, i think they just look a lot bigger in the picture and the way it was taken
How about now? Look a little smaller?
Last edited:
You need smaller loops, preferable a single one or a thinner wick to avoid flooding the deck due to over-wicking, less is more in that case
Last edited:
You need smaller loops, preferable a single one or a thinner wick to avoid flooding the deck due to over-wicking, less is more in that case
so technically i could just have 1 loop coming up into the fluff? I just went by the other build pictures and it showed that he used loops about the size of the end of your finger, which is the size they are
Yep! Even an edge is fine most of the time, depending of your resistance of course.
Hi!! I haven't been around in a very long time. Still lovin my sphearoids and now wanting the Heron to go with my paps that should be here any day. So it looks like I missed out on the first run. When will they be available again? Thanks.
So it looks like I missed out on the first run. When will they be available again? Thanks.
Hi!! I haven't been around in a very long time. Still lovin my sphearoids and now wanting the Heron to go with my paps that should be here any day.
There is no release announced yet but keep an eye out on vapourart.com or subscribe to this thread http://www.e-cigarette-forum.com/fo...ifications-tips-tricks-updates-thread-10.html
Perseas will post on that thread the upcoming vapour days. It's just closed for us posting to it...
Welcome to the club, btw.
Welcome to the club, btw.
So I think yesterday, it was when PayPal completed my payment for the pre-order...
Must mean ship time is near!
Must mean ship time is near!
Using .30ga 7/8 wrap on 1/16 micro jig with SnC cotton. I originally built the coils vertically. I decided to slant the coils ever so slight to "aim" the wicks towards the wick hole in the cap. The wicks fit perfectly through the top cap without choking them or too much "room"
Here are a few pics and I will not put this down for days. Perfect heat, great GVC flavor and good times.
It absolutely wicks and is my best build. The juice transfer from the fluff to the wick is incredible from the Heron.
I left 1 cm on each laying on the deck to soak every drop!
Thank you again Perseas.
Here are a few pics and I will not put this down for days. Perfect heat, great GVC flavor and good times.
It absolutely wicks and is my best build. The juice transfer from the fluff to the wick is incredible from the Heron.
I left 1 cm on each laying on the deck to soak every drop!
Thank you again Perseas.
^Gr8 job there iDBro√ Fantastic build. Waiting for my second to replicate this build.
- Status
Similar threads
