Posted a brief review of the polished stainless tank here.. http://www.e-cigarette-forum.com/forum/canada-forum/226667-review-depth-charge-tank-vapor-age.html#post4206363
- Status
Posted a brief review of the polished stainless tank here.. http://www.e-cigarette-forum.com/forum/canada-forum/226667-review-depth-charge-tank-vapor-age.html#post4206363
Oh, wow! I reeeeeally like that!!!
Can't wait til they are available for sale. I assume you got yours in Vegas?
yes and the Pyrex is a good thing too... i used to worry that they weren't spec but realize the caps give plenty of room to cover irregularity on one end...and you get the red stripes too.
Has anyone heard from Jonah? I wonder how his recovery is going... Hope he is doing well.
This as of 3 days ago.. There were some minor complications during Surgery, but he is on the road to recovery.
So, both my last two attempts at filling and refilling the tank has led to leaking from the bottom of the carto connector. Not sure what I am doing wrong, but I'm damn well going to figure it out. 
That being said, it does not leak once I've got it all back together. It just leaks when the carto gets sealed in the tank. I guess it forces the juice through the carto hole and down past the connector.
That being said, it does not leak once I've got it all back together. It just leaks when the carto gets sealed in the tank. I guess it forces the juice through the carto hole and down past the connector.
So, both my last two attempts at filling and refilling the tank has led to leaking from the bottom of the carto connector. Not sure what I am doing wrong, but I'm damn well going to figure it out.
That being said, it does not leak once I've got it all back together. It just leaks when the carto gets sealed in the tank. I guess it forces the juice through the carto hole and down past the connector.
Try putting the cap back on just to the o-ring and then turn the tank upside down before pushing it all the way on...see if that helps you.
Try putting the cap back on just to the o-ring and then turn the tank upside down before pushing it all the way on...see if that helps you.
Also, with the side hole/slot submerged in the liquid and the top cap off, liquid will start seeping it's way into the carto since the tank is no longer pressurized. It's really not too big of a deal. If the carto becomes flooded during a tank refill, just give it a quick short blow into a paper towel and all should be well.
I like my CEs better than standard "filled" cartomizers, so it's actually an all stainless CE tank. This way when the CE dies someday my husband can rewick it with ss mesh.
Jonah just had everything beautiful at his booth. He had the nice jewelry cases with glass tops displaying everything. I picked up some blown glass drip tips from him as well. I'm really hoping that he puts them up for sale. I just can't keep thinking about the STERLING silver drip tips he had.
Here are 2 photos with the SS tank on the Prodigy V3.1, & of course another of Jonah's tank on the P-18. It fits the P-18 like a glove
(one pic is the tank on the prodigy with the 510/510, & the other pic is of the tank with no adapter.)
The SS tank is beggin' to have something laser engraved on it. Can't wait to get a couple and have some fun with 'em
Posted a brief review of the polished stainless tank here.. http://www.e-cigarette-forum.com/forum/canada-forum/226667-review-depth-charge-tank-vapor-age.html#post4206363
Now those are some beautiful things. Got to get one.
I like my CEs better than standard "filled" cartomizers, so it's actually an all stainless CE tank. This way when the CE dies someday my husband can rewick it with ss mesh.
Jonah just had everything beautiful at his booth. He had the nice jewelry cases with glass tops displaying everything. I picked up some blown glass drip tips from him as well. I'm really hoping that he puts them up for sale. I just can't keep thinking about the STERLING silver drip tips he had.
Here are 2 photos with the SS tank on the Prodigy V3.1, & of course another of Jonah's tank on the P-18. It fits the P-18 like a glove
(one pic is the tank on the prodigy with the 510/510, & the other pic is of the tank with no adapter.)
Oh my God, you are wonderful. It looks Great on the ProdigyV3. I am totally sold now.
Thank You very much for your pictures BMWJEN
So I've been playing with my Torpedo Tank and I am getting massive leaking from the bottom. Not the threads area but the sides of the bottom (around the edge of the plastic tube). When I put juice into the tank (only filling about halfway) it seems to be fine. Then after a few hours I notice juice drops coming out the bottom, then I get a little juice running down the sides of my battery. I store it on its side overnight and once I screw it onto the battery, juice comes dripping out and after a few hours its pouring out. Today I had to dump all the juice in it into a sink as I had no place to put it and juice was getting everywhere in my bag.
I am noticing that juice is filling the area below the bottom O ring. Is this supposed to happen? Any idea on what's wrong or how I can fix it?
Thanks!
Edit: I re watched the video on the "Battle of the Tank Mods" and her Torpedo Tank seems to be much tighter. I can take off the bottom and top of my Torpedo tank really easily. I don't need to do all the wiggling she did. Just a little screw motion and pull and it comes right off.
I am noticing that juice is filling the area below the bottom O ring. Is this supposed to happen? Any idea on what's wrong or how I can fix it?
Thanks!
Edit: I re watched the video on the "Battle of the Tank Mods" and her Torpedo Tank seems to be much tighter. I can take off the bottom and top of my Torpedo tank really easily. I don't need to do all the wiggling she did. Just a little screw motion and pull and it comes right off.
Last edited:
Sounds lilke an o-ring issue to me. I would send it back for Jonah to look at. It may take some time with his health issues. Or go to a hardware store that has a large selection or orings. You would want one just a hair thicker.
The orange o rings allow the caps to come off quite easily. I have them and have never had anything like you discribe. The only issue with leakage I have ever experienced is with the CE2s, never with any other area at all. The black o-rings reguire wiggling like you saw in the youtube.
If you have the pirex tube I would not mess with it AT ALL! Send it back in.
The orange o rings allow the caps to come off quite easily. I have them and have never had anything like you discribe. The only issue with leakage I have ever experienced is with the CE2s, never with any other area at all. The black o-rings reguire wiggling like you saw in the youtube.
If you have the pirex tube I would not mess with it AT ALL! Send it back in.
So I've been playing with my Torpedo Tank and I am getting massive leaking from the bottom. Not the threads area but the sides of the bottom (around the edge of the plastic tube). When I put juice into the tank (only filling about halfway) it seems to be fine. Then after a few hours I notice juice drops coming out the bottom, then I get a little juice running down the sides of my battery. I store it on its side overnight and once I screw it onto the battery, juice comes dripping out and after a few hours its pouring out. Today I had to dump all the juice in it into a sink as I had no place to put it and juice was getting everywhere in my bag.
I am noticing that juice is filling the area below the bottom O ring. Is this supposed to happen? Any idea on what's wrong or how I can fix it?
Thanks!
Edit: I re watched the video on the "Battle of the Tank Mods" and her Torpedo Tank seems to be much tighter. I can take off the bottom and top of my Torpedo tank really easily. I don't need to do all the wiggling she did. Just a little screw motion and pull and it comes right off.
If you don't hear from Jonah soon, send me a PM with your mailing address.....I have an extra set of gaskets I can send you
Hope you get well soon, Jonah!
I'm just waitin' to pull the trigger on a Torpedo Tank once they're available again.
Got the ProVari, steel Fluxos and clear drip tip. Just need a tubing cutter from Sears and I'll be ready for when Jonah is!
Thanks,
Lee
I'm just waitin' to pull the trigger on a Torpedo Tank once they're available again.
Got the ProVari, steel Fluxos and clear drip tip. Just need a tubing cutter from Sears and I'll be ready for when Jonah is!
Thanks,
Lee
Last edited:
Thanks SheerLuckHolmes and, wow, what a generous offer Para, thank you! I did order 2 replacement O ring sets with my Torpedo tank, so now that I know that may be the problem, I can try and replace them and see if that fixes it. I'll work on it tonight and test it over the next couple of days. I'll post back when I know if that worked or not
Thanks!
Thanks!
- Status
Similar threads
- Locked
