Introducing Torpedo Tanks.

[ED-209]

I did take the fam out last night, it was to see another modder/machinist but I did take them out.

LMAO...thanks for the update and info and no rush just excited that's all.

I am trying to teach myself to punch cartos, got me a one punch tool from Lowe's last night and use that for the small hole and open it up more with a nail. Not sure if I am supposed to use a hammer with the punch tool since it's called one hand but oh well, it's spring loaded and was only $5. It's not pretty but it'll do. Now just trying to figure out what kind of device or tool to use to hold them in place, I got some clamp but doesn't work that good, then thought about a vice but not sure that'll work either.

Quick question, are those regular 510 cartos (stainless) on your site Boge version? I know you have punched ones but saw those were SLB.

Thanks again and will wait patiently or try at least

 

[JonahNM]

LMAO...thanks for the update and info and no rush just excited that's all.

I am trying to teach myself to punch cartos, got me a one punch tool from Lowe's last night and use that for the small hole and open it up more with a nail. Not sure if I am supposed to use a hammer with the punch tool since it's called one hand but oh well, it's spring loaded and was only $5. It's not pretty but it'll do. Now just trying to figure out what kind of device or tool to use to hold them in place, I got some clamp but doesn't work that good, then thought about a vice but not sure that'll work either.

Quick question, are those regular 510 cartos (stainless) on your site Boge version? I know you have punched ones but saw those were SLB.

Thanks again and will wait patiently or try at least

All the cartos I have are regular size SLB, XL smoktech.

 

[MXBNW]

Is there a coupon code for the site?

 

[tyleris12]

Is there a coupon code for the site?

Try ECF10 for 10% off

 

[MXBNW]

Try ECF10 for 10% off

Thanks .....

 

[JonahNM]

Looks like I will have a table at Vegas Vapefest let me know if you are going.

 

[Pete54]

Here's a simple solution to protecting the filler when either slotting, drilling or punching a hole in a carto. Take an old SS tube and use a dremel with cutting wheel to cut a section from as shown in the picture below. Now slide it between the carto and filler. Works great and is easy to make!

 

[HzG8rGrl]

Thanks for the unbelievable Customer Service Jonah, you rock♥

 

[JonahNM]

Thanks for the unbelievable Customer Service Jonah, you rock♥

Your welcome, I do the best I can.

 

[JonahNM]

Here's a simple solution to protecting the filler when either slotting, drilling or punching a hole in a carto. Take an old SS tube and use a dremel with cutting wheel to cut a section from as shown in the picture below. Now slide it between the carto and filler. Works great and is easy to make!

Thanks for a great tip Pete.

 

[Para]

How far up the tube is the optimum location for punching? I've read 6mm up the tube section and I've read 9mm so I'm not sure what's accurate?

Thanks

 

[Greeny]

I need some feedback. If I have my friend make a jig and punch set for cartos how many people want one?

Put me down for a jig/punch set too Jonah.
Could you supply tube-cutters as well? It'd be nice to
get all that with your tanks & cartos all at one place.

 

[strprswpr]

I'll take a jig setup too.

 

[MXBNW]

I will take a jig and punch set up for standard cartos.

 

[JonahNM]

How far up the tube is the optimum location for punching? I've read 6mm up the tube section and I've read 9mm so I'm not sure what's accurate?

Thanks

So far I am finding 11 mm up the tube section to be optimum but I would guess it changes from one tank design to another.

 

[JonahNM]

I will take a jig and punch set up for standard cartos.

The Jig I am having made will be for both standard and XL cartos.

 

[JonahNM]

Put me down for a jig/punch set too Jonah.
Could you supply tube-cutters as well? It'd be nice to
get all that with your tanks & cartos all at one place.

I will look into it, but it may take a little while as I am very busy right now.

 

[MXBNW]

The Jig I am having made will be for both standard and XL cartos.

Sounds good Ill take one for sure.

 

[Para]

So far I am finding 11 mm up the tube section to be optimum but I would guess it changes from one tank design to another.

I'll hit it around 11mm. I'm MacGyvering a jig and want to put the guide in the right spot. Thanks

 

[Pete54]

Another trick I learned from heymichael is that if you take the small (mouthpiece side) condom from the top of a Boge Carto and put it on the connection side, it pretty well marks exactly where to make your cut/hole. This measurement works for any bottom cap that is the same height as the Map Tanks. I believe Jonahs are the same height. Prior to using this method I was cutting mine at 13mm.