Looked at different places but cannot find that size....anybody a good ebay reference or something, thxs!
Last edited:
- Status
I'm not sure if Blu told you guys................ But I thought I'd follow up on the earlier post made in Part 1
These do not work as a "glass tank"........ the diameter is to large
Guitar Slide + FREE 'Bottleneck for Beginners' Guide Blues Bottle Neck Gifts | eBay
so I'd recommend not ordering them
These do not work as a "glass tank"........ the diameter is to large
Guitar Slide + FREE 'Bottleneck for Beginners' Guide Blues Bottle Neck Gifts | eBay
so I'd recommend not ordering them
Kami - I mentioned it to lorderos, not sure if others saw though.
Thanks for posting that ..... they were WAY too big!! LOL
Thanks for posting that ..... they were WAY too big!! LOL
i am happy with the less fragile acrylic tank. However I am noticing I may be tightening my battery tube is cutting into the little black flat piece under the tank. I feel this could be potentially detrimental to my pv is that correct?
Also I tried the burn only on my mesh and then heated up the coil after I put it on by activating the connection and dropping a few drops of fresh juice on the glowing coil to help cheat stylie break it in. it tastes amazing. if it starts to gunk up alot or lose flavor instead of making a new wick and coil I am going to try the rinse method I heard of that way I don't lose my setup. Does anyone have any good tips about when rinsing the tank out there is always a few pesky drops of water residual stuck in the corners that my syringe won't reach and my tenticles can't get it either. how'd ya do it?>??
Also I tried the burn only on my mesh and then heated up the coil after I put it on by activating the connection and dropping a few drops of fresh juice on the glowing coil to help cheat stylie break it in. it tastes amazing. if it starts to gunk up alot or lose flavor instead of making a new wick and coil I am going to try the rinse method I heard of that way I don't lose my setup. Does anyone have any good tips about when rinsing the tank out there is always a few pesky drops of water residual stuck in the corners that my syringe won't reach and my tenticles can't get it either. how'd ya do it?>??
riel - I don't worry about the few drops of water, I just add my juice and go on about my business. LOL
I flick the drops out as well as I can and then just fill it up.
tip for cleaning coil gunk...
Fire the coils till the gunk turns to ash then while the coil is still glowing hot rinse under cold water. Dry lightly with a paper towel and repeat till everything is clean. Dry again and do a turn and burn to start the wicking again. It will be fantastic. You will have a fully broken in and fresh clean coil and wick. Flavor and vapor are AMAZING after doing this. Trust me, I have been doing this for a very long time with fantastic results every time.
You know it's time to finally replace the wick when this stops working.
You can replace the wick without needing to replace the coil if you wrapped the coil properly. If everything is right, you should be able to remove and replace the wick without breaking the coil at all. My coils tend to last a very long time, through at least 2 wick changes
Ok, I think everyone on the face of the planet takes longer hits than me!
No wonder I don't get vapor like that, I can't possibly inhale that long.
(I used a piece of band-aid pad on my Kick)
No wonder I don't get vapor like that, I can't possibly inhale that long.
(I used a piece of band-aid pad on my Kick)
They must ............ I gag in heavy fog
Ok I missed it...what size magnets? ........... same as the GG switch? ... or????
Just ordered the magnets: 10mm dia x 2mmA x3mm dia csk hole NORTH N42 magnets that was all I could find and some Cyanoacrylate adhesive.
This is what lorderos posted .... I think some got them from eBay.
They are 8mm OD x 3mm ID x 1.2mm thick.
yeahh could not find them so I took the advice from POC on the magnets, should be ok I hope, paid more for shipping than what they actually cost
I followed these instructions:
Katana - Modifications and DIY - UK Vapers - Page 73
The link lord had put up did not work this morning, now it does but they don't ship internationally. The one's I ordered should be ok I guess....I hope...
Katana - Modifications and DIY - UK Vapers - Page 73
The link lord had put up did not work this morning, now it does but they don't ship internationally. The one's I ordered should be ok I guess....I hope...
- Status
Similar threads
