I run imr n redilasts. The redilasts use the Panasonic cells and outperformed both the aw imr n ic cells. Will try n find the thread on candlepower.com
Katana by POC ~ Show and Tell :)
- Thread starter UA72Riddle
- Start date
- th_trl_thread_readers 0
- Status
These one's all the way:
Callies Kustoms 3100mAh 18650 Panasonic Batteries
And then the IMR's on that page
Callies Kustoms 3100mAh 18650 Panasonic Batteries
And then the IMR's on that page
Last edited:
You need more heat or you need to hold the button for a few seconds to allow it to heat up before the first drag. With a solid wick there is alot of mesh and juice and it takes a while to heat that up.
The IMRs will outperform the flat tops every time
. The may not last quite as long, but they can deliver 10 amps of current where the flat tops are protected to about 3 or 4 amps which means you cannot get the same wattage from a flat top that you can from an IMR.
totally agree!!!
The IMRs will outperform the flat tops every time
Thanks Yellowman1972, that was not necessary at all but is appreciated.
For installing the magnets, here is what I did.
Remove the switch and take the screw out that comes in contact with the battery... make sure you hold the switch together as you do you you will need to chase a small spring down, lol.
Take the spring and button out of the swtich and then put the screw back in. Put one magnet in and then take 2 other magnets and stick them together. Test against the other magnet to make sure you are putting these in so that the are pushing away from the other one. Put those on the screw and they should be repelling away from the other one in the switch already. They should push away just enough that the screw is long enough to hold them and have a few threads left so you won't need to hol it all toghether as you do the next step.
Put the bottom of the switch back in and screw the switch back together again.
Now you have a magnetic switch
The IMRs will outperform the flat tops every time
Boys and their watts..........Thank you LordGodMod
I stick with the AW IMR. Nothing wrong with the Panasonic at all, the IMR simply outperforms the models you've listed
.
Boys and their watts..........Thank you LordGodMod
You ladies should mind you're watts as well. It determines just how much vapor you can produce. Without enough watts, it does not matter how low a resistance load you present to the battery and if you present too low a resistance, the battery that cannot supply enough current for the load goes ka-bloowie
This has been a public service announcement from lorderos33
You ladies should mind you're watts as well. It determines just how much vapor you can produce. Without enough watts, it does not matter how low a resistance load you present to the battery and if you present too low a resistance, the battery that cannot supply enough current for the load goes ka-bloowie
This has been a public service announcement from lorderos33
hmmmmmmmmmm......sorta' sounds like the inverse of a boy I once dated
So guys I've been talking to someone who blows glass tubes, and I told him about the dimensions of the katana tube, and asked if he could do it. He is going to see what he can do, if all goes well we have a glass supplier for tubes!
This will be great if he's willing to test fit them, as there were inconsistencies in the order from the UK.
Katana v3 coming tomorrow!!! Oh happy day! Got my wick oxidized.n.primed. Thx for all the tips.guys. one thing i have noticed.is.hella.people break their tanks. The zen thread is.rife with it.are they that fragile.or.are people.forgeting that while it resembles atube.mod it is far from it
The quartz is not that fragile either, it was just the first run of the mods, the tanks did not have the edges flame polished so they concentrated all their stresses on the edge of the tanks. The new quartz tanks have flame polished edges and should be far more durable than they were.
The acrylic tanks are still more durable but for glass the quartz should be much better now than it was. I have a few of the flame polished tanks and so far they seem much better in use (and less sharp
)
Is it just me, or does juice consumption actually decrease when the wick breaks in? I filled up the tank yesterday (10am) and used it all day - and when I got home (9pm) it was a little over half full... and I vaped pretty consistently all day... lol
Agree, it's great. But I lost both my tanks in a week at work. my mods don't sit on a desk, or in a case.
They get used, and used hard, haha.
I find that mine uses more juice once the wick breaks in, b/c once it really starts wicking, I tend to just chief on it non-stop until it needs a refill. Though I must say, and I tend to burn through a lotta juice while trying to break it in! Especially when I turn it upside down and fire it until juice starts to drip out of the wick
no joke rwechsler I have still been playing with figuring out the right siz of wick lately I have been cutting my length of wick right around 45mm long and probly 30 mm wide but I rinse my mesh in instant hot boiling water then finger wipe it dry. then I put juice on it and burnit as soon as the fire goes out I put drops of juice on it to build the oxi and its still so hot it vapes as it coats the wick one end to the other.
ps does anyone have a reference or hookup for a long blunt needled tip for syringes that fit the original hole in the v3 for filling. I modded a needle tip bottle and a different blunt tip needle that fit inside the needle tip bottle needle to extend it so I didn't have to tamper my wick and coil setup when refilling. (due to me liking the longer wick setup for holding reserve juice when I just reef on it like im chuggin a beer.)
ps does anyone have a reference or hookup for a long blunt needled tip for syringes that fit the original hole in the v3 for filling. I modded a needle tip bottle and a different blunt tip needle that fit inside the needle tip bottle needle to extend it so I didn't have to tamper my wick and coil setup when refilling. (due to me liking the longer wick setup for holding reserve juice when I just reef on it like im chuggin a beer.)
Last edited:
- Status
Similar threads
- Locked
