I have seen this posted prior here. I have not had the bad gravity issue. Others have had luck, using a small hammer or object, forcing the tank back on. Small impact to straighten the tank. Then unscrew & reinstall tank as usual. No leaking reported.
- Status
I have seen this posted prior here. I have not had the bad gravity issue. Others have had luck, using a small hammer or object, forcing the tank back on. Small impact to straighten the tank. Then unscrew & reinstall tank as usual. No leaking reported.
j3suss, there have been several people who have done the same thing. Basically, they unscrewed it and rescrewed it and it was OK. BUT...DO NOT listen to me. I have no first hand experience. But there are those who frequent this thread who do. So be patient and wait for a reply. Your situation is fixable but make sure you get proper instruction.
Hello mates,
Yesterday I dropped my kayfun to mod the floor. The problem is that a thread of kayfun not unscrew. I tested with latex gloves, my hands, and I do not know what to do, the thread is very hard ...
What can I do? : (
Thank you very much!
I had the same problem with a clone, what I did was gently tap it on a table until the chimney lined back up in the center.
try wrapping some blue painters tape around the tank right up to the seem you want to unscrew, then wrap another piece around the lower tank section right up to the seem too, tape overhanging way past the part on each side will aid the grip... you should then be able to grip each and just unscrew it.... this also works well for any high end mod that winds up getting stuck tightly at the threads, no pliers here 
Here is what i did to my R91 this am. Its a clear kit & clear tube combo.
on my v2 paps
picture of the cotton wick in the chimney
Works great, i can see the fluid touching the cotton wick ends. Coil should look nice in the dark.
Brake down of parts. OEM R91%
http://www.ultravaping.com/product-p/h-ta-kayfuntubel.htm
https://www.fasttech.com/p/1570900
12.00 for the clear 22mm tank
5.12 for the clear parts set
I dont like the 23mm oem clear tank. Have one sitting around since July. I have OCD & like flush, seamless
on my v2 paps picture of the cotton wick in the chimneyWorks great, i can see the fluid touching the cotton wick ends. Coil should look nice in the dark.
Brake down of parts. OEM R91%
http://www.ultravaping.com/product-p/h-ta-kayfuntubel.htm
https://www.fasttech.com/p/1570900
12.00 for the clear 22mm tank
5.12 for the clear parts set
I dont like the 23mm oem clear tank. Have one sitting around since July. I have OCD & like flush, seamless
Last edited:
Holy crap where did you get that from!! It's beautiful
Sent from my iPhone using Tapatalk
j3suss, if you bugger the clear tank section, here it is for 3 bux Kayfun Short Hybrid Tank
I have a Hcigar 3.1 that will be here Thursday my first kayfun. Will this fit the Hcigar?
Sent from my SGH-M919 using Tapatalk
Hi Guys~ I don't have any Kayfun's yet and thinking of going for a Mini 2.1 ES from Cloud 9 Vaping. Besides the full kit are there any other accessories that would add to this kit. Also see this is available at Vaperev but looks like it's $45 bucks more.
How much is shipping and how long should it take to get from Cloud 9 Vaping to U.S.?
How much is shipping and how long should it take to get from Cloud 9 Vaping to U.S.?
thats only the clear window section, but the links in my above post should all fit the Hcigar clone. Check Tanks for 12. clear long hybrid tank. There long tank, i am using. Also a nano hybrid tank on there site.
note: i am not affiliated with this site. I just like to pimp my gear with nice after market stuff.
I've ordered from C9V before, and I believe it was to me in 5-7 days. Granted that was back in the summer, so my memory may fail. Only issue is the VAT. So do the math, because it may be for cost effective to order from VapeRev. C9V is a reputable supplier though. I've no issues in the packages I received. Plus you get a piece of candy
I've ordered from C9V before, and I believe it was to me in 5-7 days. Granted that was back in the summer, so my memory may fail. Only issue is the VAT. So do the math, because it may be for cost effective to order from VapeRev. C9V is a reputable supplier though. I've no issues in the packages I received. Plus you get a piece of candy
For me, it was more like 7-10 days, but mine was around New Years, and the big winter storm. I am pretty sure the prices quoted include VAT, it says quite clearly on their website. The Kayfun mini does not come with a drip tip, so get one if you need it. C9V includes a nice squeeze bottle with a luer lock cap and plastic needle tip for refilling the KFM.
Well thanks for that. I just got shipping notice for the clear set of parts from FT and didn't even notice the 23mm diameter. I'm not quite so OCD, so I'll wait 'til it gets here to decide if I want the ultravaping version. I'm thinking it'll just be for fun & education anyway. I already like the original all SS sections or 1/3 clear section combos.
This sounds intriguing. I'm going to have to look into this, thanks.
Hello mates,
Yesterday I dropped my kayfun to mod the floor. The problem is that a thread of kayfun not unscrew. I tested with latex gloves, my hands, and I do not know what to do, the thread is very hard ...
What can I do? : (
Thank you very much!
I did the same thing last week bent bad!
I used a pair of water pump pliers and a paper towel around the plastic and some brute force...the thread snapped back in and unscrewed fine...I did put a couple of lite scratches on the plastic tube but it works fine and I'll replace it sometime soon.
Last edited:
Ok sorry but way to many post to go through. Is it possible to rewick a micro coil with sterile cotton in the KFL without taking it apart?
Mine floods bad. Not when vaping but when I take it off, the bottom is covered in juice. Using 70PG/30VG. 30 guage with 8-9 wraps around a .069 diameter bit. Vape is fantastic. Wetness ticks me off.
Mine floods bad. Not when vaping but when I take it off, the bottom is covered in juice. Using 70PG/30VG. 30 guage with 8-9 wraps around a .069 diameter bit. Vape is fantastic. Wetness ticks me off.
Without taking it apart? I'm not following you on that one.
Yes, it is possible to rewick a micro coil with whatever medium you choose, but you do have to disassemble the KFL down to the base to access the coil.
Maybe he means without sucking the juice out?? Either way its gotta come apart
- Status
Similar threads
