- Status
Dual coil of Mundy's magic and 26Ni. Meters in the .4 range.
The 26 heats fast giving big heat and vapor while the MM heats slow adding in those trademark MM high sweet notes.
Build is in a Trident that has been modified into a catfish.
(Sorry for the crappy pic)
Sent from the zoo using Tapatypo 2
The 26 heats fast giving big heat and vapor while the MM heats slow adding in those trademark MM high sweet notes.
Build is in a Trident that has been modified into a catfish.
(Sorry for the crappy pic)
Sent from the zoo using Tapatypo 2
First the disclaimer!
IF YOU DO NOT HAVE THE ELECTRONICS TO SAFELY PRODUCE VOLTAGES BELOW 1.5 VOLTS AT UP TO 20 AMPS THIS WOULD BE DANGEROUS!
DOING THIS WITHOUT THE ELECTRONICS WOULD OVERTAX ANY BATTERY AVAILABLE AND WOULD BE THE EQUIVALENT OF A DEAD SHORT!
Not sure where to post this set up.
It technically doesn't fit here since there isn't a coil, but the mesh roll fits "micro".
400 mesh.........that's it, well washed unoxidized 400 mesh.
0.065 ohm on 20A VV Grand set to 1.23V for 19A at the coil.
Don't worry kids, I have 1-AW 18650 in it and the input amperage at the battery is only 6.4A.
A+ for vapor.
B+ for throat hit.
B for flavor.( Above protank, below Rene41, and further below Magic )
C for lag time
When I get my lathe so I can make custom atties I will work on the flavor production.
IF YOU DO NOT HAVE THE ELECTRONICS TO SAFELY PRODUCE VOLTAGES BELOW 1.5 VOLTS AT UP TO 20 AMPS THIS WOULD BE DANGEROUS!
DOING THIS WITHOUT THE ELECTRONICS WOULD OVERTAX ANY BATTERY AVAILABLE AND WOULD BE THE EQUIVALENT OF A DEAD SHORT!
Not sure where to post this set up.
It technically doesn't fit here since there isn't a coil, but the mesh roll fits "micro".
400 mesh.........that's it, well washed unoxidized 400 mesh.
0.065 ohm on 20A VV Grand set to 1.23V for 19A at the coil.
Don't worry kids, I have 1-AW 18650 in it and the input amperage at the battery is only 6.4A.
A+ for vapor.
B+ for throat hit.
B for flavor.( Above protank, below Rene41, and further below Magic )
C for lag time
When I get my lathe so I can make custom atties I will work on the flavor production.
The wick is the coil!!!!! = Mind Blown!!!!!
Agree with MIND BLOWN AWAY!!!!!!!
^ now that ya mention it, why, yes, I am
Hmph!
Sent from the zoo using Tapatypo 2
'S funny how different it sounds when a monkey says "hmph". 
almost sounds messy.
almost sounds messy.
Stuck on 24hr doodie... Err... Duty
My mm/26n coil was too lopsided. The 26 heated too fast. Broke out my battery case and my extra wire and made this nasty thing. Nothing to pinch with, so I just pulsed and strummed until it heated.
I think it's about 13 wraps each metering at 'holy-poo this heats slow' ohms.
Not a bad vape though
Sent from the zoo using Tapatypo 2
My mm/26n coil was too lopsided. The 26 heated too fast. Broke out my battery case and my extra wire and made this nasty thing. Nothing to pinch with, so I just pulsed and strummed until it heated.
I think it's about 13 wraps each metering at 'holy-poo this heats slow' ohms.
Not a bad vape though
Sent from the zoo using Tapatypo 2
I always picture Clint Eastwood with him when he does that. Wait, are you guys old enough to get that?'S funny how different it sounds when a monkey says "hmph".
almost sounds messy.
First the disclaimer!
IF YOU DO NOT HAVE THE ELECTRONICS TO SAFELY PRODUCE VOLTAGES BELOW 1.5 VOLTS AT UP TO 20 AMPS THIS WOULD BE DANGEROUS!
DOING THIS WITHOUT THE ELECTRONICS WOULD OVERTAX ANY BATTERY AVAILABLE AND WOULD BE THE EQUIVALENT OF A DEAD SHORT!
Not sure where to post this set up.
It technically doesn't fit here since there isn't a coil, but the mesh roll fits "micro".
400 mesh.........that's it, well washed unoxidized 400 mesh.
0.065 ohm on 20A VV Grand set to 1.23V for 19A at the coil.
Don't worry kids, I have 1-AW 18650 in it and the input amperage at the battery is only 6.4A.
A+ for vapor.
B+ for throat hit.
B for flavor.( Above protank, below Rene41, and further below Magic )
C for lag time
When I get my lathe so I can make custom atties I will work on the flavor production.
No worries about trying that on my end. I can't even figure out what you did there!
26n xobedriver on the chalice. Epic cloud machine!
Sent from the zoo using Tapatypo 2
Sent from the zoo using Tapatypo 2
I have been vaping unicorn blood as my all day vape for a while now. When I fill the bottle, basically daily, I have to rewick. By the time my bottle is getting low the juice starts getting dark. Is this normal? It seems like I have to rewick quite a bit. Maybe it's just unicorn blood gums it up quick?? I am using a 6 wrap 28g kanthal coil at about .85 ohms with rolled cotton wick.
- Status
Similar threads
