Older Folks and Vaping Front Porch - Part 2

Status
Not open for further replies.

DavidOck

ECF Guru
Supporting Member
ECF Veteran
Jan 3, 2013
21,239
178,485
Halfway to Paradise, WA
I see all the EHPro Kayfuns. Anyone have a Tobeco?

Tobeco KF clone? Yep. Well make, although it did come with a bad o-ring, either bad from their supplier or pinched at the factory. No problems with it otherwise, and all the parts seem to be interchangeable with my EHPro ones.
 

Wolfenstark

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2014
4,815
14,724
Perth , Australia
Theres not much to this dripper for something to be wrong - Though the gold plating reflects the light a lot on the base when I'm under a light trying to see to build it.

Its very tight when getting the deck out of the base - even after a few uses have to push it hard with a tea towel.
 

mekc57

Super Member
ECF Veteran
Verified Member
Oct 27, 2013
530
2,748
Oregon
I have one more question. When you are loosening the air screw will it stop on its own or just keep unscrewing till it comes out?
The air screw comes all the way out if you keep going? The air kit your talking about doesn't have a screw/air control. It's a new air tube that's just full wide open with more air for bigger, hotter builds. I got one but will probably never use it. This has plenty of air from the factory for most people. If your into dual coils and all that, they use the big air kit!
 

MattB101

Ultra Member
ECF Veteran
Jul 9, 2012
2,560
74,146
67
Deerfield Beach, FL
Thanks I'm sure it will have a learning curve just like the KFL's did when I started with them. I use cellucotton and by the looks of it it doesn't fluff up quite as good. I'm going to have to watch some more videos. Theres a lot not in English though.

My cellucotton (rayon) fluffs just fine. :D
 

Ken_A

Vaping Master
ECF Veteran
Verified Member
Jan 13, 2013
4,876
28,345
Florida
It was with an Australian store - don't know what they would charge for USA delivery

i'll look to see

Nope they only deliver here or New zealand

Well there starting price was high so with the code and the exchange rate was around $34 USA dollars

Though the only stores in usa i found near that price wanted $29 for postage to send to me.
You may want to buy more locally.
Juice Concentrates - Hangsen - Juice Factory
 

Wolfenstark

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2014
4,815
14,724
Perth , Australia
Most of the time the prices here are higher.

Too many store owners want to make as much money as other people in other countries do while selling a tenth the amount.

You find the occasional item priced ok.

Too many people buy on their credit card and don't like the feeling of oh this price is too high for me.
 

Wolfenstark

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2014
4,815
14,724
Perth , Australia
Got a link?

I got this one but as i was saying its probably much cheaper in a USA store. - Don't know why i got it from there unless at the time it may have been sold out in other stores I usually go to.

Plume Veil RDA - Clone | VapourEyes

k4 clone
Tobeco Kayfun 4 Clone NO LOGO - Kidney Puncher

Pre Order Kayfun 4 V4 RBA Atomizer Clone by Tobeco Ships Free | eBay

probably other places

http://www.ebay.com.au/itm/PLUME-VE...LONE-STAINLESS-BLACK-AND-COPPER-/141412656523
 
Last edited:

Wolfenstark

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2014
4,815
14,724
Perth , Australia
Don't know much about the k4 just what i read from people who have one or couple of reviews.

Still got to go back to the why couldn't they put features of v4 into v1 ,2, 3

Or are they using some technology or material that was recently invented.

The plume veil is ok if you want to drip drip drip but to try out some liquids quicker than a tank its ok- theres one called a magma which has deep juice well -

features of other ones people talk about don't interest me.

though it comes with this top cap and some demilitarised plastic thingy - delirium insulator sumfin.

I use this other chuff drip tip - when i use the original and put the coils so they are in line with the air slots the coils are too close to the plastic.
 
Last edited:
Status
Not open for further replies.

Users who are viewing this thread