PDIB's Making MODs!

[timk]

Day 4 of vaping the new silver contact is the same as day one. The only think that's touched it (since I fine tuned the installation) is the negative side of my battery and it touches it often.

flawless. Hits every press. Hard. I'm gonna add a wrap to my next coil because the added voltage makes this 1.2 ohm coil a bit warm for my preference

With all this reduced VD folks are gonna have to rethink their sweet spot

So much for a modder's mod if no modding is required just kidding, that is great because I am lazy and would rather mix juices chasing that dragon instead My wife will be pleased to know this one requires no tinker... haha that's what I sell anyway.

Gettin pretty excited over here... waiting... patiently... strike that, can be patiently waiting if you say you are patiently waiting, that's just waiting impatiently


I'm good, no need for the thorazine yet, just excited!

 

[SeaNap]

Flawless. Hits every press. Hard. I'm gonna add a wrap to my next coil because the added voltage makes this 1.2 ohm coil a bit warm for my preference

With all this reduced VD folks are gonna have to rethink their sweet spot

Thanks for pointing that out Supe. Thats what we've been saying all along. There have been people who think that we were just being silly trying to reduce v-drop and that it didn't matter for those that did not sub-ohm. I tried along time ago to explain the benefits using math, but I think that point gets forgotten and people start to associate better connectivity with sub-ohm and they thumb their nose at it.

I really dislike that Rob called the new kits 'Sub-Ohm Kits' for the REO. While the new kits definitely let you run sub ohm coils, the main benifit is just making the mod all around more efficent and better for your battery. IMO they should have just been called a performance upgrade, or increased conductivity kit (im terrible at naming things but you get what i mean)

That's amazing to hear that the silver is holding up so well! Can't wait till I get mine!

 

[super_X_drifter]

Great point fellow Georgian.

Perhaps High Efficiency Contacts or High Output Contacts would have been better suited.

I got a couple of HO's coming in Thursday
Mostly case I loathe noalox and applying anything greasy to my mods

And Timk, this is a little mod . The original contact was aluminum and the original spring was whatever the flim flammin dibber dabber deemed appropriate.

Yes, I too can mod

 

[Filthy-Beast]

Thanks for pointing that out Supe. Thats what we've been saying all along. There have been people who think that we were just being silly trying to reduce v-drop and that it didn't matter for those that did not sub-ohm. I tried along time ago to explain the benefits using math, but I think that point gets forgotten and people start to associate better connectivity with sub-ohm and they thumb their nose at it.

I really dislike that Rob called the new kits 'Sub-Ohm Kits' for the REO. While the new kits definitely let you run sub ohm coils, the main benifit is just making the mod all around more efficent and better for your battery. IMO they should have just been called a performance upgrade, or increased conductivity kit (im terrible at naming things but you get what i mean)

That's amazing to hear that the silver is holding up so well! Can't wait till I get mine!

Totally agree and I also keep posting that after the upgrade to get the same hit increase the ohms of the coil and get better battery life.

 

[turbocad6]

Thanks for pointing that out Supe. Thats what we've been saying all along. There have been people who think that we were just being silly trying to reduce v-drop and that it didn't matter for those that did not sub-ohm. I tried along time ago to explain the benefits using math, but I think that point gets forgotten and people start to associate better connectivity with sub-ohm and they thumb their nose at it.

I really dislike that Rob called the new kits 'Sub-Ohm Kits' for the REO. While the new kits definitely let you run sub ohm coils, the main benifit is just making the mod all around more efficent and better for your battery. IMO they should have just been called a performance upgrade, or increased conductivity kit (im terrible at naming things but you get what i mean)

That's amazing to hear that the silver is holding up so well! Can't wait till I get mine!

I agree with this too, it's not a "sub ohm" kit. it's a "fix the crappy contacts" kit

any resistance that is not the coil itself is robbing you of power, just because it vapes ok with a high ohm coil don't make it good, saying it works ok at higher ohms is like saying it doesn't matter that my gas tank leaks a little because I get such good gas milage anyway

 

[supertrunker]

Too bad i can only like that once! Superb post.

T

 

[Bimini Twist]

....It's gone.. my friend doesn't remember where she put it.

O.M.G!

And I never say that.

I'll catch up later, but owwww!

 

[Bimini Twist]

I wonder if the people that have one already just sit there and stare at them? Or does that wear off after having it awhile?

I try, but I go all cross-eyed. It's so hard to stare at while it's in a fog-filled room - even though it's right under my nose.

 

[MasterofNone]

Ok so it's an idea I've been floating over in reoville... Now that there are 1:1 clones coming out, what say you, modders: the TOBH atty, modded for bottom feeding? Anyone like the idea? Hate it? And anyone think you can run single coil on these?

Sent from my iPhone using Tapatalk

 

[SeaNap]

I'd be curious to know if the AFC has options for single or dual coil set ups like the Cyclone AFC does

I think the center post is copper, so it would be easy to drill into submission but some people may worry about their juice coming into contact with the copper.

 

[supertrunker]

i thought it really depended on the airholes and whether you had to block some off or not. Atties like a Helios are just not really geared for single coils, since there's no way, short of covering up or filling things to leave just one open.

I have drilled an igo-w4 to bottom feed (took me days, but that needn't matter now) and with duals it's a beast. The point of the fins on the top of the TOBH are to cool it off some, according to reviews i've seen, and apparently they work.

Just to make you feel guilty, i was looking at them the other day and they were out of stock (so what's new??), but are made by a father and son team. Better to just buy the clone and rip those guys off! ??

T

 

[MasterofNone]

Lol my point T was I'd be willing to tinker with a cheap atty than a well built handcrafted beauty. I break things. It's... What I do, apparently. Lol

Silly metal monster


Sent from my iPhone using Tapatalk

 

[supertrunker]

It's what i do too! I have dremelled a cheap Scar atty too to b/f and that works in either single or dual coil because the air comes from underneath the coil in either case. i think it cost me $8!

So give it a bash!

T

 

[MasterofNone]

Bash is probably what I'll end up doing lol


Sent from my iPhone using Tapatalk

 

[Rossum]

Oh my. I'm practically at a loss for words, but that piece is amazing.

Monkey has bid on the monkey pod.

OK. In that case, I shall refrain.

 

[ValHeli]

Ok, onto s'more woodies!!!

I sure hope these turn out looking good in person

Quilted Sapele: 19.5" x 5.25" x 1.25"

Resin Casted Amboyna: 1.25" x 4.25" x 5.5"

 

[ValHeli]

This one looks interesting. The wood is common in the PHilippines but this is the first time i've seen it like this:

Quilted Narra: 17 7/8" x 5 1/2" x 1 7/8"

 

[ValHeli]

Not a fan of Hawaiian Curly Koa but THIS just looks fabulous

 

[glassgal]

For those of you with multiple types of bottom feeders.... how big is the difference in vape quality between your best and worst ones (and which are which)? IS there a huge difference between say the RM2 and the Chalice or Cyclone? What's that difference? Thanks.

 

[ValHeli]

I wouldn't know about the Chalice but I have plenty of RM2s and Cyclones. If I place the same type of coil and Ω in all of them, they're all the same to me in terms of vape quality.

The biggest taste and performance difference for me in any atty is in the coil and cotton. My favorite coils right now is the Magic Mundy and braided 3 strand 30g and I vape them at .8Ω - 1Ω wicked with KGD (koh gen do pure cotton)