Nice coil. What's your thoughts on the 40? I've been itching to pull the trigger but I'm not sure.
The Giraffe
- Status
The Giraffe
It hasnt completely replaced my mech as i still like the form factor and power i get with low ohm builds 0.15-0.25ohm range on something simple. But for my tanks and when i just want a relaxing vape , its perfect. The temp control with nickel is growing on me, i thought it was a bit cool on my first builds but the clapton build above is closer to my mech builds for denser warmer vapor, so i think with some more practice with the nickel i will be able to replicate my mech even with only 40w.
Even if the nickel is not for you then its a rock solid 40w vw with amazing battery life.
Even if the nickel is not for you then its a rock solid 40w vw with amazing battery life.
probably 0.1mm x 0.8mm thats one of the standard ribbon sizes
Agreed, o love how fast it throttles up / cools down . . And that temp control is pretty cool too huh.. I need something I never have to worry about polishing / cleaning contacts on. . .I gave away my provari and only had tines fir a while and was dying having to constantly polish.
It is SATURDAY!!
That means I spent the better part of the morning at my workbench wrapping coils!
All coils are wrapped with 29 gauge twisted wire.
My A7 RDA @ .6ohms. This is my taste tester, with center air flow. I finally got the build to sit right over the airflow!
Sorry camera would not focus on it, but as you can see it focused on my felt work station.
My REO RM2 @.6ohms
The Vulcan @.5ohms (dual coiled)
The Dark Horse @.5ohms (dual coiled)
And the coil jig that makes these awesome wraps possible.
I made it out of dowel Rod, and drilled holes in both ends and use different sized finishing nails depending on coil size I want.
Then I stuff wire in to the hole, and push the finishing nail in and twist naturally tight coils. (or at least the best coils I have made).
That means I spent the better part of the morning at my workbench wrapping coils!
All coils are wrapped with 29 gauge twisted wire.
My A7 RDA @ .6ohms. This is my taste tester, with center air flow. I finally got the build to sit right over the airflow!
Sorry camera would not focus on it, but as you can see it focused on my felt work station.
My REO RM2 @.6ohms
The Vulcan @.5ohms (dual coiled)
The Dark Horse @.5ohms (dual coiled)
And the coil jig that makes these awesome wraps possible.
I made it out of dowel Rod, and drilled holes in both ends and use different sized finishing nails depending on coil size I want.
Then I stuff wire in to the hole, and push the finishing nail in and twist naturally tight coils. (or at least the best coils I have made).
After wasting an obscene amount of time and kanthal figuring out how to build these . . .
and they are working nice. not about to swear by them but in a day maybe things will change
5 wrap 24 gauge parallel around a blue screwdriver (approximately 2mm). Metered out to 0.09 ohms. Pretty nice vape on my ipv3. Vaping it around 50-75 watts.
Magma with 10 Gauge (2.5mm) air tubes 0.35Ω 0.9mm X 0.1mm flat ribbon NR-R-NR and trimmed tails Rayon.
After wasting an obscene amount of time and kanthal figuring out how to build these . . .
and they are working nice. not about to swear by them but in a day maybe things will change
Did you use my tutorial picks?
s far as dripper builds go, I like nothing better so far, then my stovetops
Sent with one hand, the other is busy vaping.
New tobh Delrin cap/tip combo with af for quads
22ga quads Netting 0.3ohm
you sure thats 0.3ohm, 22g quads at what looks about 2mm id come out below 0.1ohm on my calcs. Just thought i would mention it incase you have a dodgy ohm reader.
Loving my kayfun again..... Dual stacked coils, 28 gauge kanthal @ .7 ohms
Sent with one hand, the other is busy vaping.
What? No off set?
Good looking out my friend. It's a 28.5mm tobh. It just looks really good on this 26650 feeder.
Running quad coils on my RDAs.
28 awg A1 with 1.3mm id.
The Patriot is 7/8 wrap. Mutation X is 6/7 wrap.
Both come in at 0.26 ohm.
28 awg A1 with 1.3mm id.
The Patriot is 7/8 wrap. Mutation X is 6/7 wrap.
Both come in at 0.26 ohm.
Last edited:
- Status
Similar threads
