It's not soldered it's welded, search nr-r-nr welder. You cab build one. I think they are super cool.YOyo Yo AMD TRUCKING..... the ribbon builds you are doing with the NR wire, is there a certain solder that is best for this? Thanks
- Status
Double barrel in the kayfun. Best vape I've had off a kayfun to date.
Per the stovetops from a couple days ago - I didn't use the tutorial, but maybe I should have. Just wrapped them on these little watch punches that came in a watch repair kit I bought from amazon. I think that if I tightened them up they'd work better. Right now they are more like snail coils than stovetop coils.
Built another parallel with 22 gauge and twisted 26 gauge since I liked my last one so much. Except this time I wrapped it around an appox. 2mm screwdriver. Came out to .14 ohms.
28g wrapped around 24g
Combo wrapped 3/4 around 1.5mm screwdriver.
Can't find my ohm meter to get exact reading but my ipv2 shows 0.2 ohm.
The ramp up time is crazy fast and cool down takes a while.
any pointers here?
I'm running dual 8 loop 24g (maybe 26 I forgot) at .35 ohms and it's not giving me the flavor nor the vapor using a plume veil with chuff cap wide open
I'm running dual 8 loop 24g (maybe 26 I forgot) at .35 ohms and it's not giving me the flavor nor the vapor using a plume veil with chuff cap wide open
any pointers here?
I'm running dual 8 loop 24g (maybe 26 I forgot) at .35 ohms and it's not giving me the flavor nor the vapor using a plume veil with chuff cap wide open
only thing I am seeing is less wick?
and make sure it is not super tight in side the coil
it's rayon and I think I have whe wick figured out, it works great in all my other setups...
I'm thinking maybe to many loops or too much ohms for a double at 24, my perfect dripper setup is roughly the same ohms (.35-.4) using a single 24g
I honestly never tried Reo. I'm not sure why do I need it.
This Panzer stock was NOT the best vape I ever had. The Airflow was too tight and it was leaking a little. Long story – short, I had my way with it. I drilled horizontal air holes 2.5 mm and drilled vertical holes to install 10 Gauge hypodermic needles 2.5 mm. The vape is great now and it no longer leaks.
Last edited:
Nice, the "magma shooter" . I know you'e into tanks ,obviously but all the same convenience one handed no spills and tons of capacity with a dripper , I'm telling ya, it's the way to go.
And I didn't stay reo.
And I didn't stay reo.
I just can't vape on something you have to "squonk"
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
^truth.
Dripping = unscrew bottle cap. Drip drip. Make sure you don't overdrip. Screw cap on
Bottom feeders = Squonk
Burping out loud using Tapatalk
Dripping = unscrew bottle cap. Drip drip. Make sure you don't overdrip. Screw cap on
Bottom feeders = Squonk
Burping out loud using Tapatalk
More in love with the plume veil than ever before.
I'd been using it with 28ga, then got a tobh (copper, for a copper SMPL clone), stillare, 26, and 24ga to play with.
Best vapor production I've ever had, beating out some slightly lower ohm setups (0.37 lowest). Simple 26ga around 2mm, coils dangerously close to the top cap, but oh so smooth. I could go back to 18mg and it'd stay velvety, I believe.
Oh yeah, the chuff cap kicks ... with the PV, big time.
I'd been using it with 28ga, then got a tobh (copper, for a copper SMPL clone), stillare, 26, and 24ga to play with.
Best vapor production I've ever had, beating out some slightly lower ohm setups (0.37 lowest). Simple 26ga around 2mm, coils dangerously close to the top cap, but oh so smooth. I could go back to 18mg and it'd stay velvety, I believe.
Oh yeah, the chuff cap kicks ... with the PV, big time.
i have a bottom feeder that i stopped using almost a year ago for many reasons, in my experience mech tubes and batteries need far less cleaning and upkeep, i was using 0.2Ω coils on the BF and needed to clean the battery terminals/batteries every 4 days or so to keep it performing without gaining to much VD, i could go atleast a month on tube mod without needing to clean and i dont get pitted battery terminals like i used to & i'm even vaping higher wattage now(0.15), at a guess i'd say the dif in cleaning is about 90%, and yes i used to use noalox and no i dont use it anymore
- Status
Similar threads
