- Status
I got this! I got this!..Magus7091 
coils with wick to follow
Mine came to 0.12ohms, should be good on the mech.
coils with wick to follow
Mine came to 0.12ohms, should be good on the mech.
I rebuilt mine with 22, but it's nowhere near as uniform as that. It came out to 0.16.
Edit
Additional information added.
Edit
Additional information added.
I don't have that istick, BUT....it screws down flush on the RX200...and that mod has a pretty short 510 connector, so I think you will be fine.
I haven't had any issues...and when you clapton it that way, ramp up time isn't nearly as quick...remember, on a clapton, the bulk of the current goes through the path of least resistance....which is the larger wire. The outer wire is heated more through its contact with the center wire. Add to that a working TC set up, the wire should never get hot enough to be damaged.
No man! lol i already said you did a good tidy job!
It's only because ive had lots of practice making diamond coil's which are pretty much the same process, they were always good flavour coils to.
I used 24g 316SS, its nice and soft
4x 12wraps, 2.5id, 0.12ohms, it tastes good
Thanks USM. I still worry though because the rx200 has a little "juice cup" that sits about a millimeter below the surface of the mod so attys may appear to sit flush even if they are in actuality not :/. My TM atty "appears" to sit flush on my rx200 but there is quite a noticeable gap when I screw it on my iStick.
Do you have any CompVape attys to compare the 510 pin/thread length to that of the Tsunamis? I'll be very upset if my black tsunami doesn't sit flush on my black iStick. It's meant to replace the black Velocity clone that I have on it now since I think it's dying... The resistance changes with different mods (different 510s) and sometimes it just displays "no atomizer" message leading me to believe there exists a 510/insulator issue.
Thanks. I'll think about ordering some smaller gauge Ti though I already find it annoying how tedious it is to clean/rewick my Ti/Ka fused claptons as I have to take so much care in dry-burning to avoid the TiOxide (sp?) issue.
This isn't my coil or photo, but it's so damn pretty I had to share.
twisted ribbon stovetop.....I have done clapton stovetops, but I still haven't ever used ribbon wireThis isn't my coil or photo, but it's so damn pretty I had to share.
Shes a geometric beautyThis isn't my coil or photo, but it's so damn pretty I had to share.
Edit: i'm gonna have to try this lol
no compvape attys, but the tsunami 510 is very similar in length to the V1 kanger sub tank (the 7ml one)....longer then the cubis, shorther then the Rose V2...same length as the dark horse.
Going a bit further with that logic, I'd say that since my kanger subtank 7ml sat flush on my istick, there shouldn't be any issues.
I was having issues like that with my tobeco symbiote rda, so what I ended up doing was to disassemble the positive post, slightly modify the peek insulator, then flip it, so the screw just caught a couple threads on the block. This solved that issue, as well as really tightening down the post block. Haven't had any issues with it since. If you want to try this, since you're planning to replace the velocity anyway, I'd be happy to post a pic or two to show you.
This is my first build like this. I usually just do regular duals, twisted or parallel. This one is a 24/32g Clapton paralleled with 24g. Just put the rayon in and its hittin pretty good.
Ok, so this is my very first (not just first successful, actual first)cat track coil. All ss304 26awg dual 3wrap .22ohms. Pic is taken through the atomizer (just got the ice cubed yesterday on a trade from a buddy that manages a local vape shop, really happy with it,thanks Aaron @ MASTERVAPOR general booth Va Beach) if anybody has tips or tricks for making these easier ill take some (@SLIPPY_EEL , and @Tom Forde im looking at you guys when i say this)
- Status
Similar threads
