Prodigy Is Now in Your Hand or Shipping Info Recieved
- Thread starter Cancer
- Start date
- th_trl_thread_readers 0
- Status
Your POOPS have never smelled better than at 5volts
I just hope there are replacement switches readily available.
Your POOPS have never smelled better than at 5volts
LOL now for 10 points who said the origanal quote ...hint its someone on this board !
You sure it is the switch? Try cleaning the threads on the bottom cap and end of the case. There seems to be quite a bit of residue from something on them that is non conductive.
Brian
I think it may be a faulty resistor. After I got a dead drag twice in a row, I swapped out batteries, and then a double dead drag again, then I swapped atomizers, same thing, another atomizer, same thing. Then I unscrewed everything and noticed the resister on the back of the switch was warm, reassembled and repeated all of the following over again.
It's bound to happen, you can't get that many resistors and not have one fail. Hopefully PS can send a replacement switch out and I'll be back in business. What I'm most upset about is that I like a dumb ... I only took the prodigy to work with me today. I should have known better...
don't be so hard on yourself! I probably would have done the same thing. Yet I got the passthrough as well..so that would have saved me there. Steve will take care of you!
Steve .. talking about his SB ...
DING DING Ladycats wins Ten points .....err now dont spend them all in one place
good job ...dang now i gotta find a new quote tonight when i get home from work
I just got mine and looks like my batteries dont have enough charge in em yet. I did a quick 10 minute charge on a set and i'm getting a good throat hit the batteries are alittle weak at the moment.
One note my BE112 Atomizers dont work as in dont screw in it looks like the the center of the atomizer is out to far for the threads to catch.
Also I didnt get an atomizer in my package I'm gonna shoot u guys an email in a few.
Cant wait for my batteries to charge!
One note my BE112 Atomizers dont work as in dont screw in it looks like the the center of the atomizer is out to far for the threads to catch.
Also I didnt get an atomizer in my package I'm gonna shoot u guys an email in a few.
Cant wait for my batteries to charge!
well...not sure what actually did it, but i did all those things steve suggested and now it is vaping up a storm!!!!!!
cant get either the adaptor or end cap all the way down snug but its working for now....and Im gonna ride this vapor train till the batteries die beforel opening it up to switch batts and see if it is still working.
cant get either the adaptor or end cap all the way down snug but its working for now....and Im gonna ride this vapor train till the batteries die beforel opening it up to switch batts and see if it is still working.
I think it may be a faulty resistor. After I got a dead drag twice in a row, I swapped out batteries, and then a double dead drag again, then I swapped atomizers, same thing, another atomizer, same thing. Then I unscrewed everything and noticed the resister on the back of the switch was warm, reassembled and repeated all of the following over again.
It's bound to happen, you can't get that many resistors and not have one fail. Hopefully PS can send a replacement switch out and I'll be back in business. What I'm most upset about is that I like a dumb ... I only took the prodigy to work with me today. I should have known better...
UNLUCKY mate hopefully you will have more look with a replacement!
thing is with that many resistors is this going to be an on going problem for prodigy?
Bad luck for sure. Can you bypass the resistor at all, or is it too cramped? Also can you get a reading on the resistor?
this is a MOD, so switches or resistors can be "touchy". Yet the Prodigy has a 6 month warranty, so no worries
Frankly ... Assuming you sent in a ticket, I can shoot you a replacement housing/switch/resistor/etc...
There are
I think it may be a faulty resistor. After I got a dead drag twice in a row, I swapped out batteries, and then a double dead drag again, then I swapped atomizers, same thing, another atomizer, same thing. Then I unscrewed everything and noticed the resister on the back of the switch was warm, reassembled and repeated all of the following over again.
It's bound to happen, you can't get that many resistors and not have one fail. Hopefully PS can send a replacement switch out and I'll be back in business. What I'm most upset about is that I like a dumb ... I only took the prodigy to work with me today. I should have known better...
Haven't seen a faulty resistor yet, but its definitely bound to happen
You may have tapped TOO much on the adapter ... hehe ... Give it about 2 weeks for the spring and threads to break in and become smoother to assemble
First one I have seen Kit, so not sure. The resistors we have used locally have withstood alot and haven't had one pop yet!
Ok i'm learning how to use this better..I just got a good head rush..that hasnt happened in a long time lol....Anyways I'm learning i have to screw in the atomizer all the way in and then turn it back 1/4 or 1/2 turn for there to be a solid connection. Can someone else try there bestecig 801 atomizers to see if they fit..I'm glad i held off on buying 20 before it came. So far the generic and original atomizers work just fine although i like the generic better right now it gets HOT!
I must say i'm loving this thing!! Thanks for all the hard work from you and the staff!
I must say i'm loving this thing!! Thanks for all the hard work from you and the staff!
Last edited:
you beat me to it sorta......as i was sitting here vaping and noticed the atty was a little bit wiggly....as soon as i put it down snug it stopped working....backed it off so it was wiggly again and it worked again.
thanks for everyones help.
- Status
Similar threads
