Omg, this whole time I thought it was the Kotex U pads, it's the tampons lol, I didn't know that. Thanks for the link! Tomorrow, I already left the market.
Rayon Wick - Better Flow, Flavor, Longevity, and Nic Hit!! - Pt.2
- Thread starter JeremyR
- Start date
- th_trl_thread_readers 0
- Status
The Limitless looks like the best design so far but I don't have one. I don't think there is a 22mm version. Side fill after removing the top cap.
The Avocado I took the orings off the reducer and looped a piece of thin kanthal through the air hole, then twisted the ends and cut off the excess, leaving a small tip. Now to refill I pull off the cap, and remove the reducer by grabbing the tip.
The Avocado I took the orings off the reducer and looped a piece of thin kanthal through the air hole, then twisted the ends and cut off the excess, leaving a small tip. Now to refill I pull off the cap, and remove the reducer by grabbing the tip.
LOL, sorry I do avoid using that word. Their just little Rayon bullets.
Have you seen my video review and build with KU?
I'm looking at the op right now... Man I can't believe I did all that on a first edition moto g phone... I see I didn't put that video up..
Here it is.
Rayon wicking tutorial & a look at KU
It's ok, I did see that vid on your YouTube channel. I thought you pinched it off the pad. Pretty funny!
I remember you listing it in your order of preference liking it more than Sally's Graham, right?
But Sally's Graham was a bit easier to use.
It's a different type/grade of rayon, it's a more dry looking type and has some different attributes. The packaging isn't great for the rayon, it's all compacted, but you can't get that type of rayon other than from the melatonin (. ect) bottles.
The bottle rayon, all that I've seen are the dry type. The bottle rayon would be a better choice to use, more uniform and easier to work with... As was shown a few pages back the fiber is nice, straight, and even.
Either way they both cost about 5.00 to try.
The bottle rayon, all that I've seen are the dry type. The bottle rayon would be a better choice to use, more uniform and easier to work with... As was shown a few pages back the fiber is nice, straight, and even.
Either way they both cost about 5.00 to try.
Last edited:
Thanks for the tips, JeremyR, PaulNHC, and kross8! I did forget to mention that my Subtank is the newer version, so I have the larger juice holes in the RBA (no need to bust out the Dremel, haha). I have a pancake in right now that's holding steady (credit to NickN and his post on pg. 3 of this thread for the idea), but whenever it's had enough I'll give JeremyR's tip a try.
I do have to ask, are you suggesting a "mullet-style" cut: having a thicker part of the wick sticking straight out and cutting flush with the chamber wall, then leaving a longer, thinner tail hanging down towards to deck and juice holes? Or just a thinned tail, cut to the diameter of the RBA, hanging down from coil towards juice holes? This reminds me that I'll have to recover my old Photobucket password to post pictures of whatever I come up with...
I do have to ask, are you suggesting a "mullet-style" cut: having a thicker part of the wick sticking straight out and cutting flush with the chamber wall, then leaving a longer, thinner tail hanging down towards to deck and juice holes? Or just a thinned tail, cut to the diameter of the RBA, hanging down from coil towards juice holes? This reminds me that I'll have to recover my old Photobucket password to post pictures of whatever I come up with...
I use 90vg/10dw diy. I make a 2.4 or 2.5 coil, rayon wick (google points) just tight enough to drag, pull the ends up like bunny ears, slide the ring down, cut the ears off straight about a 1/4 inch above the ring. Then stuff little by little with a small flat screwdriver. I can always trim later if dry or stuff little bits in gurgley.
Muah! Cyber hug for you! Thanks! You guys are so kind!
I'm so sorry, I could've sworn there was a 22mm one. I can't find it either. But on myvaporstore it's $26.95, vaperoyalty $26.50, on FT $18.~ it was $20 on code3vapor for July 4th but it's sold out. I'm going to check Daniel from DJLSB Vapes video on YouTube, I could've sworn it was Daniel who said there was a first run with 22mm.
No need to feel sorry, too much stuff these days to keep it all straight.
May have been a pre production sample that was 22mm.
May have been a pre production sample that was 22mm.
there was a bunch of it heartsdelight. maybe 20' or so. It will surely last a long time. rayon is all it's been cracked up to be imo, and i'm happy i switched from cotton. I did go back to my beloved titanium wire tho after giving 316l a trial. the ss worked well in tc mode, but in the end i find i like the ti wire better.
thanks again, dear, for the generous sample of rayon, i'm gonna stick with that for my wicking. i'm pretty much satisfied with my vape gear atm and haven't been posting much of late. i keep telling myself i can only vape one thing at a time and as i have 2 nice tc mods and 3 good rta's along with 2 stm's i've been able to resist "shineyitis". i am looking at the new dna75's tho...........
My pleasure! Was just trying to help out the guy who lost his delivery. Shineyitis... Must stop... Lol, stocking up for the vape apocalypse. I ordered on preorder the SMY SDNA75 $66 I know SMY's track record in the past was meh. But since Daniel from DJLSB Vapes fine tuned the firmware & it comes pre installed, you can still go to escribe if you want, I took the chance. Received it, it's nice & compact, same size as Evic Vtc mini but more rounded, nice hand feel. Will play with it this weekend. I'm surprised that they haven't sent it to YouTube reviewers not much info on it.there was a bunch of it heartsdelight. maybe 20' or so. It will surely last a long time. rayon is all it's been cracked up to be imo, and i'm happy i switched from cotton. I did go back to my beloved titanium wire tho after giving 316l a trial. the ss worked well in tc mode, but in the end i find i like the ti wire better.
thanks again, dear, for the generous sample of rayon, i'm gonna stick with that for my wicking. i'm pretty much satisfied with my vape gear atm and haven't been posting much of late. i keep telling myself i can only vape one thing at a time and as i have 2 nice tc mods and 3 good rta's along with 2 stm's i've been able to resist "shineyitis". i am looking at the new dna75's tho...........
- Status
Similar threads
