Shinyitis Support Group

[Tralfaz]

Hello shinies! Just a quick question, I decided to be a total jackass and bought a 60ml bottle of juice when I already have a couple of others... Does juice expire?

You'll probably vape it up long before it will expire. The general rule is about a year. I just pulled a bottle out of my stash that's about that old and it's perfectly fine.

 

[Iotodem]

And on a side note, does anyone else have a problem with the BF 80W constantly re adjusting the ohm rating on their coils, example, ill be walking down the street Vaping at 70W .18 ohm and then all the sudden its reading .28 ohm and went down to 45W, is this a problem with the firmware update? (Updated to v007), I have dropped it once or twice so maybe a coil change?

 

[Iotodem]

You'll probably vape it up long before it will expire. The general rule is about a year. I just pulled a bottle out of my stash that's about that old and it's perfectly fine.

Okay sweet, since moving from the AL85 I'm going through like 16ml a day so yeah probably haha

 

[dom qp]

And on a side note, does anyone else have a problem with the BF 80W constantly re adjusting the ohm rating on their coils, example, ill be walking down the street Vaping at 70W .18 ohm and then all the sudden its reading .28 ohm and went down to 45W, is this a problem with the firmware update? (Updated to v007), I have dropped it once or twice so maybe a coil change?

Sounds like a leg screw needs to be down, assuming you're using the dual coil pulse X and it's going from 0.18 to 0.28ish.

Sometimes it's hard to get them down tight with little screw drivers.

 

[Tralfaz]

And on a side note, does anyone else have a problem with the BF 80W constantly re adjusting the ohm rating on their coils, example, ill be walking down the street Vaping at 70W .18 ohm and then all the sudden its reading .28 ohm and went down to 45W, is this a problem with the firmware update? (Updated to v007), I have dropped it once or twice so maybe a coil change?

If it's jumping around that much, try cranking down your post screws. Other than that, there could be something wrong with the atty. Also, maybe try some new coils.

 

[Iotodem]

Sounds like a leg screw needs to be down, assuming you're using the dual coil pulse X and it's going from 0.18 to 0.28ish.

Sometimes it's hard to get them down tight with little screw drivers.

I am using the Pulse X tank haha, okay thanks, I will try tightening everything up and see what happens, I can't remember for the life of me what the resistance is supposed to be (GM Coils, small Clapton from dashvapes)

 

[Tralfaz]

Probably closer to .18 for dual coils.

 

[Iotodem]

If it's jumping around that much, try cranking down your post screws. Other than that, there could be something wrong with the atty. Also, maybe try some new coils.

I really hope it isn't the atty... I will be very depressed if that's the case

 

[Punk In Drublic]

And on a side note, does anyone else have a problem with the BF 80W constantly re adjusting the ohm rating on their coils, example, ill be walking down the street Vaping at 70W .18 ohm and then all the sudden its reading .28 ohm and went down to 45W, is this a problem with the firmware update? (Updated to v007), I have dropped it once or twice so maybe a coil change?

Never had that problem – go over your RDA to ensure all grub screws are tight as @dom qp mentioned. But curious, what battery are you using to vape at 70 watts?

 

[Tralfaz]

I really hope it isn't the atty... I will be very depressed if that's the case

I doubt it is. It's almost always the post screws or the coils.

 

[Iotodem]

If it's jumping around that much, try cranking down your post screws. Other than that, there could be something wrong with the atty. Also, maybe try some new coils.

So the screws couldn't be any tighter, try a new coil?

 

[Iotodem]

Coils*

 

[Tralfaz]

So the screws couldn't be any tighter, try a new coil?

Yep, if the resistance is still jumping. Get a good glow on them and stroke them to get the hot spots out. You could also space them.

 

[Iotodem]

Never had that problem – go over your RDA to ensure all grub screws are tight as @dom qp mentioned. But curious, what battery are you using to vape at 70 watts?

I'm using an ijoy 20700

 

[Iotodem]

Yep, if the resistance is still jumping. Get a good glow on them and stroke them to get the hot spots out. You could also space them.

Okay, going to rebuild now, and it doesn't jump rapidly or persistantly, its almost like I jolt my hand the wrong way and the coil comes loose and then falls back into place, almost like the atty is coming loose but it's not

 

[Iotodem]

Never had that problem – go over your RDA to ensure all grub screws are tight as @dom qp mentioned. But curious, what battery are you using to vape at 70 watts?

I used an 18650 for like 2 hours then went to the 20700

 

[Tralfaz]

Okay, going to rebuild now, and it doesn't jump rapidly or persistantly, its almost like I jolt my hand the wrong way and the coil comes loose and then falls back into place, almost like the atty is coming loose but it's not

Before you swap coils, you could try cleaning the 510 on the mod and the atty really well to make sure you have a clean contact.

 

[Punk In Drublic]

Although claimed to be a 40amp battery, Mooch’s estimates is around 20amps. I’d consider dropping your wattage to 60.

 

[Iotodem]

Before you swap coils, you could try cleaning the 510 on the mod and the atty really well to make sure you have a clean contact.

Good catch! If not ill drop these .......s in haha

 

[Iotodem]

Although claimed to be a 40amp battery, Mooch’s estimates is around 20amps. I’d consider dropping your wattage to 60.

View attachment 775841

Okay