Shinyitis Support Group

[Fidola13]

@Fidola13 here is his answer.

@Fidola13 here is his answer.

Ok thanks that’s helpful. Thanks. I’m really enjoying it!

 

[NolaMel]

I do better with a magnifying lamp.
I have the one that clamps to the desk with the articulating arm.
Provides good light when needed and can look thru it when building for intricate builds.

Heck found a link:
Fluorescent Magnifying Lamp

Those are really nice too. I have a lighted bench, and prior hobbies called for higher magnification than those offered. If I was buying today, I might go with that. Just using what I already own.

 

[NolaMel]

@JamesDMad For a crisp $20 bill Ill send you one of these. Made here in Las Vegas.
View attachment 731105 View attachment 731107

A toilet paper roll holder???? You’re more expensive than Kohler

 

[untar]

I put one I know is .5 in and read .15

Is the insulator intact? Is the 510 pin properly threaded, centered and firmly seated?
I'd remove the (+) plate and double check there's no damage to the insulator.

 

[NolaMel]

I need help. Small hex screwdrivers that will work on rdas. Just need hex. My hands aren't what they used to be.

I've looked but don't have an idea what sizes rdas use, just small as hell.

They sell a set at Walmart with a ton of different sizes from minute up. Cheap, but effective. That’s a stylus next to it for size reference.

 

[NolaMel]

Seems I was wrong.

Impossible

 

[Letitia]

I don't know about Jay but me not losing 75% of those tiny heads would be a certified miracle.

 

[Letitia]

H

Impossible

Happens quite often unfortunately.

 

[Letitia]

@NolaMel forgot to tell you Flavorah has released a new line of tea flavor concentrates. Smokey Blue is testing them out now. If you go to their Web site you can follow his notes.

 

[NolaMel]

I don't know about Jay but me not losing 75% of those tiny heads would be a certified miracle.

I spent twenty minutes on the floor with a flashlight looking for the bloody tiny screw out of the rta deck. I’m a certified klutz. I’m going to start building in a plastic pan. Might be safer

 

[Skunk!]

A toilet paper roll holder???? You’re more expensive than Kohler

Oh .... thats funny! Especially now that it has the derringer and skinny drip tip on it. I have tried to keep my devices from looking like vibrators only to make them look like toilet paper holders lmao

 

[Letitia]

I spent twenty minutes on the floor with a flashlight looking for the bloody tiny screw out of the rta deck. I’m a certified klutz. I’m going to start building in a plastic pan. Might be safer

I build on my 521 tab and it catches the grubs usually. Maybe try a hand towel, doubt they would roll off of one.

 

[TrollDragon]

View attachment 731171
They sell a set at Walmart with a ton of different sizes from minute up. Cheap, but effective. That’s a stylus next to it for size reference.

Those sets might be okay for bigger screws. I'd never take one to the grubs on an atty, but that's me.

 

[Letitia]

Oh .... thats funny! Especially now that it has the derringer and skinny drip tip on it. I have tried to keep my devices from looking live vibrators only to make them look like toilet paper holders lmao

Go check out the thread For the Women next time you could use a laugh.

 

[TrollDragon]

So I'm not going to mess with this anymore tonight.

My second B2K deck won't read correctly. Every could is .13-.17, on ohe tab or on a regulated mod.

I cleaned it, checked the 510, nothing looks out of place.

Ideas?

Sounds like a piece of wire in there somewhere, what does it read with no coil mounted?

 

[NolaMel]

I build on my 521 tab and it catches the grubs usually. Maybe try a hand towel, doubt they would roll off of one.

I think I’m going to use the grid board I use for cutting glass. It’s deep enough nothing can bounce, and easy to use angle forceps to retrieve something

 

[Skunk!]

Go check out the thread For the Women next time you could use a laugh.

I'll do that! I can imagine...

 

[TrollDragon]

Thank you. My turn, need one for .25 and .5 grubs. My hexes are all getting worn and the tri tools can be trying at times.

Do you mean 1.25 and 1.5mm?

1.5mm Wiha
Wiha 96315 Precision Hex Metric Screwdriver, 1.5 x 50mm - Hex Keys - Amazon.com

The only 1.25mm ones I see are bits for dental implant tools.

 

[Letitia]

Do you mean 1.25 and 1.5mm?

1.5mm Wiha
Wiha 96315 Precision Hex Metric Screwdriver, 1.5 x 50mm - Hex Keys - Amazon.com

The only 1.25mm ones I see are bits for dental implant tools.

Apologies 2.5 x 4 and 2.5 x 3. Have I mentioned I don't do well with tools? They fit the Nano and Zeus + another one I can't remember. I need a vape butler.

 

[Letitia]

So do I just order a 2.5 hex?