Shinyitis Support Group

[virm]

I think any bottom air flow cannot be “relied” on as leak proof. Unfortunately my preference is usually bottom air flow but my fave rta is the Zeus original. Never a lead from those!! Great RTAs and for top

ye i went the topair road at first per advice to avoid the leaking (big part i gave up vaoing first time around).. but do you know, that thicksponge effect it gives, is just my thing. but i'm not sure anymore that's what always what does it.. the resriction on axial with 2 holes is kinda similar.
you know in retrospect i'm kinda happyi never done the two everyone in the world has; zeuses and rabbits. if i'd gone to a shop or taken the first advice that's probably where i woulda started. not that i know either way of they're good or bad, just researched enough to find something for my sweetness

 

[virm]

i kinda want a water pistol now..

 

[virm]

kids, no one's answered me on the masks thing_ where ya'll getting yours what sorts?

 

[chanelvaps]

kids, no one's answered me on the masks thing_ where ya'll getting yours what sorts?

I got some from my old job. Mental health clinic. I also made a few.

 

[Fredman1]

kids, no one's answered me on the masks thing_ where ya'll getting yours what sorts?

I use dust masks. When I get serious, I use my spray mask

 

[Pigs]

kids, no one's answered me on the masks thing_ where ya'll getting yours what sorts?

Virmy - local pharmacy for me but here's an online German source.

https://www.distrelec.de/en/mainten...uipment/protective-masks/c/cat-DNAV_PL_180602

 

[Fredman1]

And by pumpkin you mean this, right?

Or is a New Zealand pumpkin the same as ours?

I know they're both winter squashes. I'm just showing off some of the important stuff MasterChef Australia has taught me over the years.

LoL this is the one i'm steaming this afternoon

 

[Rob B.]

Hey y'all! Our friend @Nailz sent me a Zeus dual coil RTA that I just got today. Been watching Mike Vapes and Matt from SMM build tutorials, but neither of them say how many mm to cut the coils at. The user manual doesn't say either. I know some of you have this atty, and probably know. Could someone please help me with this. Thank you so much!

 

[Pigs]

Hey y'all! Our friend @Nailz sent me a Zeus dual coil RTA that I just got today. Been watching Mike Vapes and Matt from SMM build tutorials, but neither of them say how many mm to cut the coils at. I know some of you have this atty, and probably know. Could someone please help me with this. Thank you so much!

Gday Rob. This might help,

 

[Rob B.]

LoL this is the one i'm steaming this afternoonView attachment 884359

That's funny Fred. A few years ago, we had just picked yellow long neck squash, and zucchini from our garden, and put them on the kitchen counter. We had to go out for awhile to do something. When we got back, they were all gone, and there were little pieces of them all over the kitchen floor. Our now departed English Black Lab Ebony had gotten up on her hind feet, and ate every single one of them. There were about 10 to 12 in total. She was in the sun room hiding and looking very guilty.

 

[AngeNZ]

Hey y'all! Our friend @Nailz sent me a Zeus dual coil RTA that I just got today. Been watching Mike Vapes and Matt from SMM build tutorials, but neither of them say how many mm to cut the coils at. I know some of you have this atty, and probably know. Could someone please help me with this. Thank you so much!

Letitia gave me this table from the Coily tool website:
Log in - CoilyTool

 

[Rob B.]

When I first saw that photo it only downloaded your big dog's face and your txt. Thought maybe you were g

Gday Rob. This might help,

Letitia gave me this table from the Coily tool website:
Log in - CoilyTool

Thank you both so much!

 

[Rob B.]

Letitia gave me this table from the Coily tool website:
Log in - CoilyTool

It's asking me to log in. I can't get in to see the table.

 

[AngeNZ]

I did my first FT order in 2 months
I've got screws, ni80 30*3/38, ni80 30*2/40, ni80 MTL 0.1mmx0.3mm*4/40 staple coils, 810 to 510 drip tip adapters and a wire brush

 

[AngeNZ]

It's asking me to log in. I can't get in to see the table.

 

[Rob B.]

It's asking me to log in. I can't get in to see the table.

Never mind. I created an account. Thank you Ange!

Edit: You beat me to it. Thank you!

 

[virm]

I got some from my old job. Mental health clinic. I also made a few.

yeah, herself made a couple and we got one at the supermarket_ between itchy, sweaty and falling off an climbing up__ seriously felt more at risk having to adjust all the time. maybe after a couple more washes they'll get better

Virmy - local pharmacy for me but here's an online German source.

https://www.distrelec.de/en/mainten...uipment/protective-masks/c/cat-DNAV_PL_180602

thanks porkie_

so that's a no no on the FT, etc. china stuff?

 

[AngeNZ]

Just saw that Dovpo have another new dna75c mod released:

Odin Mini - Buy Product on Shenzhen Dovpo Technology Co., Ltd
I love the shape if it, but I doubt I'm going to love the price

 

[AngeNZ]

yeah, herself made a couple and we got one at the supermarket_ between itchy, sweaty and falling off an climbing up__ seriously felt more at risk having to adjust all the time. maybe after a couple more washes they'll get better



thanks porkie_

so that's a no no on the FT, etc. china stuff?

@charlie1465 got his masks from Sourcemore I think. I'd just buy them wherever you can actually get them, and that may mean vaping sites

 

[Skunk!]