I only have lemon and mandarin. Love the lemon but my mandarin was old stock from ECX lotus line. Need to get it fresh to judge but enjoyed the glimmer of what I got.
Ok... so I thought skrew em and loaded up the car with a bunch of Her clothes and went to our largest rescue shelter/rehab/abuse etc nearby. Same place that rejected me via the phone. They were most happy to take everything. Go figure. My trunk was full as was the back seat. I told them I have a LOT more. They said keep it coming. Her things will all be going to women and girls in need. That makes me feel real good and happy. Success, finally! Many more trips to go.
Everything I've read about MF's dark chocolate has been very positive. Many say it's not a true dark chocolate and with other flavors can be made into more of a milk chocolate. From reviews it has none of that fake plastic or tootsie roll thing going on.
This Milk Chocolate (Flavor Base) from ELR looks good.
Bavarian Cream (TPA) 3%
Dark Chocolate (MF) 1%
Sweet Cream (CAP) 1.5%
Some time ago I recall Annette from Virgin Vapor saying they use MF flavors in their juices. Their caramel, peach, strawberry and guava juices were all excellent. The wife raved about their coffee.
They have all the MF flavors here: Flavors - Premium Line
"Our Premium Flavor Line is a new addition to our products and is replacing our old Genuine Flavor line and will most closely match the old line in flavor and concentration."
I have a growing list of MF flavors to get.
Morning shinies
@markfm read through this thread, they might have suggestions to help:
LC?: FastTech Forums
So far the only thing that annoys me with the DL FL is the fixed chimney position, but that is mainly because I keep lining it up back to front So I'm looking forward to the DL for that reason. Plus I want to compare the different airflow between a 2 x 3mm insert and a 4mm insert on the original - whether it's any different with 2 holes or 1 
@markfm read through this thread, they might have suggestions to help:
LC?: FastTech Forums
So far the only thing that annoys me with the DL FL is the fixed chimney position, but that is mainly because I keep lining it up back to front
So I'm looking forward to the DL for that reason. Plus I want to compare the different airflow between a 2 x 3mm insert and a 4mm insert on the original - whether it's any different with 2 holes or 1 
Vapor Range LD sale: Get an extra 15% off when you spend $40 or more. Code = VRLAB15
Vapor Skinz 30% off. Code = WORK30
Vapor Skinz 30% off. Code = WORK30
I don't know if they have an ongoing code. They have several MF flavors that are 50% off sale items. No code needed.
They are pretty stingy with codes so no ongoing codes. Think this LD sale is prices marked down for a limited time on some products.
Unfortunately my fasttech mtl fl top fill is defective, obviously so. It's truly not air/liquid tight - hold it upside down, add water, and it comes out of the seam between the ss cap part and the plastic tank almost as fast as you can fill it. That's why it continuously dumps eliquid - there's no normal tank vacuum action, air comes in through that not-sealed seam and liquid goes out through the dvarw air inlet.Morning shinies
@markfm read through this thread, they might have suggestions to help:
LC?: FastTech Forums
So far the only thing that annoys me with the DL FL is the fixed chimney position, but that is mainly because I keep lining it up back to front
When I switched to the 5ml tank section that comes with the mtl fl, instead of the add-on 5ml top fill set, the dvarw works perfectly. Zero leaks, very good flavor, a just plain pleasant RTA.
My wicking was spot on, just the top fill was bad [emoji3]
Glad to hear you got it worked out. I just received 5 MTL Dvarws in the mail from FT today. I'm looking forward to trying the FL version.
I found it easy to build, though needed to drop to a 2mm coil for my Clapton wire. Rayon wicking works nice with it. The bottom fill works fine.
That's great. I love my Coppervape Dvarw, so I imagine these new ones will be really good too. I don't mind the bottom fill at all. Especially with low wattage MTL, it doesn't really go through eliquid very fast anyway.
BTW, you mentioned you had to use 2mm coils. Do you think 2.5mm coils are too large for it? I have a bunch of prebuilt ones I was hoping to use.
It all depends on the gauge of wire. I don't have any problems fitting a 2.5mm ID 26/36 clapton in my FL or older Dvarw's. With 26/30 I did have to drop it down to a 2mm ID.
ETA: That's for the MTL versions of both. lol
Last edited:
Ok, good to know. I will be using 26 or 28 single strand. So it should not be a problem then.
Last edited:
since we got that squared away.how do we add vanilla.
.25% (making sure to take note of that decimal point there... )
I should have mentioned mine are the MTL's where the space between the posts is limited compared to the DL's. Fixed my post.I fit a spaced 3.5mm 3x30/38 on DL v3 spaced and angled in mine
Similar threads
- Locked
