You need to befriend someone in the American military and get him or her to act as your go-between (there's some special cheap mailing deal for servicepeople overseas).
Hey look what i got.
Seems nice but i was immediately reminded that nautilus coils are not for me.
Hopefully my ether bridge will be here fairly soon.
Btw this is from that shop i found a couple counties away. Was out there Wednesday and he said yeah i can get it, my supplier has stock. Pulled the trigger and 2 days later its in my hand.
Given whats going on, this really is an awesome b&m.
Seems nice but i was immediately reminded that nautilus coils are not for me.
Hopefully my ether bridge will be here fairly soon.
Btw this is from that shop i found a couple counties away. Was out there Wednesday and he said yeah i can get it, my supplier has stock. Pulled the trigger and 2 days later its in my hand.
Given whats going on, this really is an awesome b&m.
For a cooler vape, 316L 32*2/38 will win over your kanthal 30*2/38 due to the smaller wires.
But if you meant kanthal 32*2/38 vs 316L 32*2/38 then the kanthal definitely will be cooler.
I thought ni80 wire would be the coolest out of the 3 different wires. But when I looked it up that coil on Steam Engine, kanthal won over ni80 as well. Here's my geeky results, all are 2.5mm id, 6 wraps, 5mm legs, 32*2/38
ss316:
Ni80:
Kanthal:
The smaller the Heat Capacity, the cooler the vape. And of course, the bigger the Surface Area the better for flavour. When I started using RDAs it was a payoff between lower Mass and Heat Capacity, yet as much Surface Area as possible.
Edited to add: I sound so geeky
Last edited:
Wanted to change flavours in the Aegis RDTA, so I washed it out, rewicked, primed it, vaped it for a bit.
Then I held it up to the light to see if my tails were too long. It slowly dawned on me that I had forgotten to fill the frickin tank
Then I held it up to the light to see if my tails were too long. It slowly dawned on me that I had forgotten to fill the frickin tank
I'm not really into pods but this looks like a good stealth device for out and about. Time to replace my old Orion DNA Go.
Cause you are. Don't go changin'Edited to add: I sound so geeky
Sounding geeky is fine. I need geeky because I am still not very knowledgeable about wires, coils, heat, ect. So do you think the kanthal 32*2/38 would work fine with 12-15 watts in my Galaxies?For a cooler vape, 316L 32*2/38 will win over your kanthal 30*2/38 due to the smaller wires.
But if you meant kanthal 32*2/38 vs 316L 32*2/38 then the kanthal definitely will be cooler.
I thought ni80 wire would be the coolest out of the 3 different wires. But when I looked it up that coil on Steam Engine, kanthal won over ni80 as well. Here's my geeky results, all are 2.5mm id, 6 wraps, 5mm legs, 32*2/38
ss316:
View attachment 942569
Ni80:
View attachment 942571
Kanthal:
View attachment 942573
The smaller the Heat Capacity, the cooler the vape. And of course, the bigger the Surface Area the better for flavour. When I started using RDAs it was a payoff between lower Mass and Heat Capacity, yet as much Surface Area as possible.
Edited to add: I sound so geeky
Definitely try that first. If you don't mind slightly less flavour, then the single clapton 30/38 is an even cooler coil:
$3.21 Authentic Superfine MTL Kanthal A1 Clapton Coil Pre-Coiled Wire - 30/38 AWG / 0.25mm/0.1mm dia. / 10pcs/pack at FastTech - Free Shipping
I've got this is ni80, and it's no springier than the 32*2/38
Abyss and ether bridge ordered
I’ll check back here next month when the paycheck comes and I can afford to hang around
I’ll check back here next month when the paycheck comes and I can afford to hang around
I’ve got a dna go and a couple regular ones I tried to sell on the classified section but there was no interest. I even had a few pods to go with them.
Ok you Taifun lovers!!
Sing along and replace the 'O' with '3' or '4' - your choice......
Sing along and replace the 'O' with '3' or '4' - your choice......
Similar threads
- Locked
