love it. so easy to build. hasn't leaked all over the place. no stupid afc pins. Honestly, I'm so allergic to afc pins now. I never want another baggy of afc pins.
I also have an augese eraaio that I really like. Both my dot styles seem a lot less fiddly then the Boro bridges.
I'm still waiting on the 909modify. That one has gotten nothing but good reviews.
That being said I do like my Boro sized pioneer. Once you figure it out you'll probably like it.
Don't use too much cotton. I dunno if the dot sized one has like the inside well inside the well. But you're not supposed to stuff your cotton all the way into the inside well.
Ive never heard of that store. Is coil clout in the US or a Chinese shop?
nvm I just found it. Kinda pricey even to me lol!
Last edited:
As I was writing that I was thinking there was something similar in my memory about that band with someone here!
you’ve got a great memory! I’m so jealous!
Is it VA Marquis 063??? If so it is very pretty!
not the Marquis although that is very pretty! the primo 503 is eye popping to me.
The Marquis I’d get would be the 012
That Primo is super nice. I wish I could bring myself to spend that much on a mod. I looked at the site and saw one I really liked but $350 is a lot to me.
I built @Fredman1's Kumo RDTA this morning and I am so impressed with it.
A wonky 2.5mm id 30*2/40 ni80 and a 2 sec. wicking job
As you guys have said, the airflow is so super smooth. And I was pleasantly surprised how much airflow there is, with just one side. But with an 810 dt or my 8mm id 510s, it's spot on.
The flavour is fantastic. I'm playing around with the coil height, as I know it can get even better. With a 2.5mm id I raised it pretty high - but it may be too high.
Any help will gratefully received!
My overall summary: It's just a frickin awesome rdta.
PS: Thank you Fred
A wonky 2.5mm id 30*2/40 ni80 and a 2 sec. wicking job
As you guys have said, the airflow is so super smooth. And I was pleasantly surprised how much airflow there is, with just one side. But with an 810 dt or my 8mm id 510s, it's spot on.
The flavour is fantastic. I'm playing around with the coil height, as I know it can get even better. With a 2.5mm id I raised it pretty high - but it may be too high.
Any help will gratefully received!
My overall summary: It's just a frickin awesome rdta.
PS: Thank you Fred
I have my coil set pretty close to the airflow. It's about 1.5mm away from the AF and raised so air hits the bottom third of the coil. I think that's the sweet spot. Any further away and I found the flavor suffers.I built @Fredman1's Kumo RDTA this morning and I am so impressed with it.
View attachment 974574
A wonky 2.5mm id 30*2/40 ni80 and a 2 sec. wicking job
As you guys have said, the airflow is so super smooth. And I was pleasantly surprised how much airflow there is, with just one side. But with an 810 dt or my 8mm id 510s, it's spot on.
The flavour is fantastic. I'm playing around with the coil height, as I know it can get even better. With a 2.5mm id I raised it pretty high - but it may be too high.
View attachment 974575
Any help will gratefully received!
My overall summary: It's just a frickin awesome rdta.
PS: Thank you Fred
My geeky self measured how far the top cap AF was inset and then I adjusted my coil from there.
Looking at your side view pic the coil looks like it could be brought closer to the AF.
Last edited:
DIY translucent Tita panel mk II !
Used the same type of plastic (lid of an old tackle box) but this time used a drill instead of a soldering iron and took my time measuring and cutting.
Went for 6 x honeycomb af holes instead of one wide oblong hole. Might change that later depending on how it vapes.
The fit is tight enough that I don't need magnets. It stays on nice and snug with no rattles.
My rough as guts workbench:
And the result:
Used the same type of plastic (lid of an old tackle box) but this time used a drill instead of a soldering iron and took my time measuring and cutting.
Went for 6 x honeycomb af holes instead of one wide oblong hole. Might change that later depending on how it vapes.
The fit is tight enough that I don't need magnets. It stays on nice and snug with no rattles.
My rough as guts workbench:
And the result:
Thanks Zazie. It suits it better than the black carbon fibre door that came with it.
Similar threads
- Locked
