Yea they got some strange colors, I just chose the black one. It already shipped, been a long time since ordered from sourcemore, so see how quick or slow they are nowadays.
good morning folks,
the parcels are in Norway, neither I nor the post office know exactly where, they are in chaos in sorting.
So, at the moment, no Kumo polishing.
One question @englishmick
Kayfun Lite Old version, where can we get glass or ss tube? Mine is 22mm
I got one glass that was a little longer, but then I need a longer dome, right?
the parcels are in Norway, neither I nor the post office know exactly where, they are in chaos in sorting.
So, at the moment, no Kumo polishing.
One question @englishmick
Kayfun Lite Old version, where can we get glass or ss tube? Mine is 22mm
I got one glass that was a little longer, but then I need a longer dome, right?
They sent the green on with the pink splatter on it for the review. I bought the one called gush grey.
@Mark Todd mentioned it in his review and I agree - if they'd continued the crown pattern engravings across the panel that covers the board, it would look so much better! Same for the battery door.
Otherwise it's pretty cool. I've always liked raw aluminium and don't mind the process of wear/polish/wear etc.
Otherwise it's pretty cool. I've always liked raw aluminium and don't mind the process of wear/polish/wear etc.
Mine are the original KFL's, EhPro clones. They are 22mm tanks, stainless top and bottom with a short plastic section in the middle so you can see the juice level. Are yours clones or genuine Kayfun?
You said glass, I know there were no actual glass parts available for the ones I have, just plastic. You could use the short plastic section in the middle, or a long plastic section that replaced both the top and bottom SS sections and the short plastic section. Either way the length of the tank stayed the same. They also came with a long SS section that replaced all three short sections, made them more robust I guess but you couldn't see the juice.
There was also a shortie version that I have a couple of. On that one the top and bottom SS sections are shorter, while the plastic section in the middle stays the same. The upper part of the chimney was shorter too.
There were numerous other options. I've seen pics of them with dome shaped tops for the tank that were either glass or plastic. Thought they were just for the later Kayfun tanks though.
For the original EhPro KFL's nothing is available to buy any more, Not sure about the genuine KFL's.
Not really sure what you are looking for. Above is all I know.
I agree.
I would also like it without all the monarchy branding, the monarchy cutout is stylish for me, maybe aluminum buttons with the logo would do the job.
One more 3F delivery question. My package is in the US now according to 17Track. I found a list of US carriers that it may be transferred to for the domestic leg including USPS and Fedex. Should I get any notification of who China Post gives it to?
If it was shipped China POST, I'm pretty sure USPS will be the truck that drops it at your house. I think FedEx would have handled it for the full trip. If you have a tracking and/or Customs number for the shipment you can enter it into the tracking for USPS and see if it shows up yet. Did you try selecting USPS in the 17Track as the destination shipper? Sometimes that works to get the secondary shipper's tracking information.
I don't know if it is original or not, it originally had one sandblasted surface, but I damaged the outside of it when I installed the wrong new o-rings, so it has been polished now. It had the SM logo on one of the rings as well.
It has adjustable AF on the side, umbraco.
That's right, it had plexiglass, the plexiglass I bought is original, but different from what I had
This is probably the Kayfun Lite (V1), because has the airflow screw on side (i don't know if it is original or not!?) !
The Kayfun Lite Plus 22mm 2014 Original (V2), it's almost the same (i don't know in dimensions, but probably they are !?), but it has the airflow screw on the bottom, different branding font on the bottom, new drip tip, on the top part of the top cap where the drip tip goes has slightly different angle cut ! Later on you could find many deferrent upper sections (chambers, chimneys, caps, bell-caps) from other moders that you could fit on the original base !
Think you got me fixed up. 17Track showed shipping info saying China Post --> unknown. I clicked on unknown and it gave me a list of possible shippers. When I selected Fedex it ignored my selection after I went back to the tracking page. When I selected USPS it changed the shipping info on the tracking page to China Post --> USPS and said USPS hasn't added any shipping info yet.
I didn't try clicking on unknown before because it wasn't highlighted and never it occurred to me to try it.
Thanks for the help.
It's complicated. I've never had one with the air screw on the side.
There was a lot of confusion about the designations. I read once that V1 meant a single air hole, V2 meant two air holes. I have a mixture of one and two air hole tanks. But I got some that were sold as V2 but only had one air hole. The clones all called themselves V2. There were some differences inside as well. I ordered several of those Kayfil tools, only the one from C de V fitted my tanks, the ones FT sold were a slightly different diameter. Mine were mostly EhPro clones, I did get one that I think was an Infinite clone and the chimney was different, and a Tobecco that had an adjustable positive pin so it could be used on a mech. Even my EhPro clones had differences in the engravings on the base part. On some the lettering was in straight lines like yours which I think is how the genuine ones were, on some the lettering was curved to match the shape of the base. I got a couple from FT that came in boxes that were faked to look like genuine Svoe Mesto boxes.
Wish I had been able to pick up some of those aftermarket parts you mentioned. Maybe they are still available somewhere but I haven't seen them. If I see any I'll let you know.
USPS usually waits for the item to hit customs before it starts updating on the tracking apps. If you use the informed delivery on USPS, you can add the Customs number to the dashboard and keep track of the US side of the tracking. Even if it says it has no record, you can add anyway and it will save it until it does enter the system.
Similar threads
- Locked
