the Aquav2 clone thread
- Thread starter roxynoodle
- Start date
- th_trl_thread_readers 0
- Status
Just got the clone by Ehpro today. The machining is good as expected. I am still playing with it and had my first build in the rta single coil mode with a 1.6 build and a tankful of Boba's Bounty. I usually test my new atties with Boba's to test the wicking. So far it's nowhere as good as the Rose V.2 IMHO, but I still have to go through the learning curve.
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
I ordered 1980802 from FT as it's the only one that's been confirmed to ship out that's still in stock. Does anyone have a line on replacement o-rings?
Dual coil. With lots of vg the Aqua works much better in dual coil. I use 28g kanthal, 1 ohm.
Moto G / Tapatalk
Be careful with the small o'ring inside the tank. It can easily go down the drain... That's what happened to me...
Moto G / Tapatalk
1 ohm is a bit harsh and not really enjoyable with 12 mg nic ejuice
I did some experimenting with the Aqua as far dual/single coils and kanthal gauges.
The draw is more restricted than what I'm used to. I ran 27 gauge duals for a while before I started to use a single coil. I like taking longer draws, but I can't really do it on the Aqua since it's on the tigher side.
To compensate I put in a single 24 and am able to take quick draws that produce very good vapor and moderate heat instead of drawing on it longer. 2-3 second instead of 5-6 second draws.
I placed my coil very close to the deck air path and it cools it fine, I feel the close placement makes it very relaxed to use. I vape 3mg in it.
The draw is more restricted than what I'm used to. I ran 27 gauge duals for a while before I started to use a single coil. I like taking longer draws, but I can't really do it on the Aqua since it's on the tigher side.
To compensate I put in a single 24 and am able to take quick draws that produce very good vapor and moderate heat instead of drawing on it longer. 2-3 second instead of 5-6 second draws.
I placed my coil very close to the deck air path and it cools it fine, I feel the close placement makes it very relaxed to use. I vape 3mg in it.
I have three of the OTM units, best combination for me has been 27 gauge duals at .5 2.4 mm. If they were still available I would probably buy a couple more. Never leak and great flavor production.
That's my mech build. I tend toward 0.7 ohm regulated.
I'm really enjoying my Tobeco one from FC. Looks like they're keeping it well stocked in their US warehouse. I bought the last one when I ordered mine, now their back in stock again.
How will it perform with 80PG juices? Any issues? Just the constitution of my hands-down favourite, by a long shot.
Don't know what everyone's using for wicking but FWIW I routinely vape DIY 20/80 in everything I own, using rayon.
Rayon here. I don't run higher than 70vg ever due to my asthma, but 70vg wicks fine.
Tobeco Aqua V2 broke the glass tank, dammm. Anyone got one they don't plan on using ? If not, who sells them ? I have the ss tank, but I'm not sure about not being able to know when low. Is there a trick to that ?
Thanks
Juh Juh
Thanks
Juh Juh
Not glass, but acrylic: $4.41 Replacement Acrylic Tank for Aqua V2 RDA Atomizers (5-Pack) 5-pack - translucent at FastTech - Worldwide Free Shipping
Get them soon - looks like they're fazing out Aqua V2 stuff...
- Status
