Ti Prometey 2 drip tank

[dspin]

U and Q - ehehe - I must vape like a child - all air controls on Prometey and Achilles for me are set at half closed. I did try full open - nasty

 

[dspin]

 

[RiverNut]

I've had 2 v1's for a while now and never had an issue with them...excellent atties. However, the v2 has leaked on me from the first time I used it. I've searched and can't find anyone else having this problem. I don't use any of them with filler, but rather as a dripper so liquid is always on the deck and slowly seeps through down through the side of the center post at the 510 connection. I haven't disassembled it completely (don't know if you can) but after removing deck/positive post, I see what looks to be an o-ring under the plastic, which apparently is not sealing properly.
Any ideas? Do I unscrew the neg post to completely disassemble? It doesn't seem to want to unscrew. Maybe a larger o-ring would fix this but I have to get at it first. Any help would be greatly appreciated.

 

[dspin]

I'll ask Alek and get back to you River - Yes you can disassemble the P2 and adjust the pin. I never looked in spare parts, but there are shims there for that. Dont understand the leaking - that is not good

 

[RiverNut]

thank you so much dspin. I've used the shims and can take off the ti deck/+ post but the neg post/plastic portion underneath doesn't seem to want to come off and I'm afraid of breaking something if I force it.
Thanks again

 

[dspin]

pm incoming to you river

 

[RiverNut]

To follow up on this just in case anyone else has this issue;
I managed to remove the negative post for complete disassembly. It was tight so I was apprehensive about it unscrewing but it does unscrew and the issue was what I had thought. I assume the o-ring that seals the positive post wasn't quite seated and thus didn't compress to make the seal. Also, if you remove the screw at the 510 connection to add a shim/washer, make sure you tighten it back tight, which compresses the o-ring making the seal.
So all is good. Thank you very much for responding dspin! I hope this info will help you help others if they happen to encounter the same thing.

I've had 2 v1's for a while now and never had an issue with them...excellent atties. However, the v2 has leaked on me from the first time I used it. I've searched and can't find anyone else having this problem. I don't use any of them with filler, but rather as a dripper so liquid is always on the deck and slowly seeps through down through the side of the center post at the 510 connection. I haven't disassembled it completely (don't know if you can) but after removing deck/positive post, I see what looks to be an o-ring under the plastic, which apparently is not sealing properly.
Any ideas? Do I unscrew the neg post to completely disassemble? It doesn't seem to want to unscrew. Maybe a larger o-ring would fix this but I have to get at it first. Any help would be greatly appreciated.

 

[qorax]

 

[qorax]

T.G.I.F.

 

[dspin]

Thanks River, glad you got it sorted. Sorry, didnt respond sooner - havent been around much

 

[aguryev]

OK, nearly had a heart attack. Got my (second hand) Prometey 2 today, and the engravings are way lighter than the v1. Looking through this thread, it seems this is normal. Crisis averted

 

[ukeman]

congrats aguryev,
I have all kinds of good RDAs... all kinds, and I have just 1 P2... if I could only have one RDA it would be my Prometey2 hands down!

Not only the best clean pure flavor of any RDA I've tried yet, but the vapor is outstanding too, AND I can fill that filler with a couple ml juice till its sopping and almost coming out over into the d/t channel (i turn the PV upside down and thread it on), and when I turn it right side up, I put almost another ml through the d/t and it doesn't leak out of the air hole.
While I vape and sense its getting dry i just add another ml or more through the d/t while tilting the PV and sort of roll it towards the filler.

Awesome RDA

I've had it for months now and I still waste my time trying others lol, but this is the one!

 

[dspin]

Congrats Ag on your P2 - my favorite atomizer in the world.


I fill exactly how Uke does.


However Uke, you need to try some Pima Cotton Sliver - P2, Achilles and all other atomizers taste even better. Unfortunately the price has gone up along with huge demand since I posted about it on a couple other forums.

 

[ukeman]

Congrats Ag on your P2 - my favorite atomizer in the world.


I fill exactly how Uke does.


However Uke, you need to try some Pima Cotton Sliver - P2, Achilles and all other atomizers taste even better. Unfortunately the price has gone up along with huge demand since I posted about it on a couple other forums.

I'm vaping Pima Sliver right now in my Big Ben Ti Dspin!
thanks for the tip my friend... pretty awsome; you get quite a lot for a couple bucks.

I am comparing it to Cotton Angel Hair from another ebay guy

 

[sllanham]

I just got the invoice for my P2 today. I'm pretty excited to say the least.

 

[dspin]

FINALLY Sll - glad to hear that. Happy for you.


Uke - I just paid for all metal Ataman since he just made the all metal tank section - so that will be my next atty from Bashik. I love his attys and hope I like this one almost as much as Prometey. If so, then it will be awesome.

 

[sllanham]

Dspin, thank you my friend. The delay was completely my fault. If I hadn't checked in with Bashik I would have been waiting forever.

 

[dspin]

Well then Sll, I am glad you double checked with Bashik, you would have missed out on a great atty

 

[ukeman]

I did this one Uke - left loop up on each side, put filler in top. Vaped great but not as good as without the filler - Outstanding vape

I was having some issues keeping the cotton wick up for the filler and it kept getting tangled on the coil so I finally decided to try silica wick like this on the Prometey2; one up for filler and one side down for base juice; I like to keep my P2 full all the time.

 

[sedge]

Just paid for a P2 and another Ataman. :rickroll :