Cthulhu RTA Discusion
- Thread starter JoshuaC
- Start date
- th_trl_thread_readers 0
-
- Tags
- cthulhu rta
- Status
Thank you, sir. Appreciate it.Nice pic
I cut some grooves in my refill ring, too. Makes it a lot easier to open it. Without the grooves I always needed pliers.
I have a cheap one.... Need a new one, it really only good for checking for shorts and the presence of voltage, which is all its original purpose was years ago when I bought it....
It jumps too much when checking internal resistance, it finally settled on 0.7 which means I was running a 0.2 build on a purple efest....
Checked my RTA again, came in t 2.0, so I have a 1.3 ohm build right now, where I expected it to be....
Just got this tank last week and I love it so far but I kept getting a little gurgle out of one side so I'm just doing a whole new build. Anybody else having issues with either the post screws or the cheap flimsy allen key that came with the tank?? Last night it got stuck on one of the post screws and it took like 15minutes to get it off. Now either most of the screws or the allen key is like stripped making it very difficult/not possible to tighten the screws down. Anybody have a place to get, or size of a replacement allen key?
@tjmmotox U can go to amazon and order a .9mm allen driver for less than 4 bucks shipped.
@rhm3769 Your resistance jumps when measuring internal because you do not have a good contact on the leads. Try taking a little fine sand paper too them then see if that helps.
Thank you for the size! I'll just go to a hardware shop tomorrow and pick one up, and look for replacement post screws as well just in case, at the moment I'm gonna try and use a spare one from my goblin, seems to fit okay.
@tjmmotox
You might have a hard time finding one that small at a local hardware store. Same goes for the grub screws. Pretty sure harbor freight will have a precision set that contains a .9mm for around 10 bucks. If not you will likely have to check your hobby shop stores as this is a common size used for remote helicopters.
I was able to get a 40-something piece precision hex and scredriver bit set that included the .09mm piece from Walmart for around $6. Works a charm for the Cthulhu and other vaping gear too.
Just got my Cthulhu Today 
I put 2 spaced 2mm 6 wrap 24 gauge coils in it, it meters out at .2.
It Wicks like a dream and Flavour is on point To be honest I never thought there would be an RTA that would work good at .2, I was wrong No need for dippers any more
I put 2 spaced 2mm 6 wrap 24 gauge coils in it, it meters out at .2.It Wicks like a dream and Flavour is on point
To be honest I never thought there would be an RTA that would work good at .2, I was wrong No need for dippers any more 
Last edited:
Just got my Cthulhu Today
It Wicks like a dream and Flavour is on point
Nice! I like that drip tip...where did you get it?
$2.33 Acrylic 510 Drip Tip (5-Pack) 5-pack - 13.5mm / black at FastTech - Worldwide Free Shipping
I like non metal DT's no lip gunk and very little heat transfer
I like non metal DT's no lip gunk and very little heat transfer
$2.33 Acrylic 510 Drip Tip (5-Pack) 5-pack - 13.5mm / black at FastTech - Worldwide Free Shipping
I like non metal DT's no lip gunk and very little heat transfer
Sweet! Got an extra one? I'll PayPal you the price of that 5 pack
I'm in Canada. Shipping would be way more than the cost of 10 of them, just order some from FT free shippingSweet! Got an extra one? I'll PayPal you the price of that 5 pack
I'm in Canada. Shipping would be way more than the cost of 10 of them, just order some from FT free shipping
Haha. Will do, thanks!
Found the RTA style "tootle puffing" sweet spot for me. 2 mm, 30 AWG Ni 200 ,15 wraps, 0.17 ohm, 32.5 watts. It's not the warm, full, wet vape of a bigger build but for those sort of mindless puffing away and enjoying every minute of it times, it hits the spot lol.
Anyone have any tips on fixing a leak from the 510 pin?
Gotta grab a picture, or host it somewhere, says my camera takes too big of a picture....
Gotta grab a picture, or host it somewhere, says my camera takes too big of a picture....
Well, sounds like garden variety leak into the bottom end which is usually caused by an air leak in the top end. Is something more going on?
Seems like it is fixed.... Just freaked out a bit I guess.... Took the battery out last night to charge it and the 510 pin was a bit leaky.... Cleaned everything up and let it sit.... Woke up this morning and checked everything out, it was still leaking a bit.... But it hasn't done it again since the first posting here....
Thinking it was a condensation issue last night and it getting down into the chamber and somehow down into the 510 pin.... I'll keep checking on it throughout the day, though.
Thinking either that, or the liquid that buids up under the drip tip went back down into the chamber....
Last edited:
- Status
