iTaste MVP v2 Owners Group
- Thread starter KnurledNut
- Start date
- th_trl_thread_readers 0
- Status
Again, SUPER THANKS GOING OUT TO COHgirl!!!! <3
One of these Surface Finish samples can be THREE skins for the MVP2! I'm pretty happy with my J-Wrap White Carbon, but I've got 2 more MVP2s coming in and I can change them out and have a brand new look!
MVP2 with White Carbon J-Wrap and future Cherry Wood Di-Noc skins
You're welcome! I'd love to see your DIY wraps!
My backup MVP arrived today too! I haven't unwrapped it yet. They really packed it well.
Wonder what color wrap to put on it?
Well it finally came!!! but, my iclear has a very tight draw. I tried taking off beauty ring and its no different. The MKP2 works great but is a very cool hit, which I am not sure I like as much as my trition. Any tips to a first time user of VV/VW? I have been playing with it and haven't really seen much of a difference until it starts to taste burnt. Thanks.
but, my iclear has a very tight draw. I tried taking off beauty ring and its no different. The MKP2 works great but is a very cool hit, which I am not sure I like as much as my trition. Any tips to a first time user of VV/VW? I have been playing with it and haven't really seen much of a difference until it starts to taste burnt. Thanks.
Here's my MVP 2 that I just received in the mail today and ordered on Friday. I have with the Joyetech eGo-CC clearomizer and pictured with it is a Kanger PT 2. Not much size difference. Might have to get another eGo-CC in black to go with this MVP..
Last edited:
Well it finally came!!!
Are you are using the iclear30 or iclear16? If you are using the 30, let the juice soak up a bit before you fire up the MVP2. Take a few drags off the tank before you screw it on. Does is gurgle? Roll up some Kleenex tight enough to fit through the little hole on the underside and soak up whatever excess you have.
Once that is done, can you start getting a hint of taste of the juice you put inside? If yes, let it sit on its side for a few more minutes.
Screw the tank back on and try to focus on the variable power option (watts) Nevermind the variable voltage for now.
Your ideal range will likely be somewhere around 7W-9W.
Thanks but it is not gurgling. when I pull on it without being screwed down I can barely get any air through. It is very tight draw. When I hit it I can get vapor but it taste like s***. oh ands its the 30.
ok so I changed wattage and it doesn't taste bad but it still VERY hard to pull. I get a lot more vapor than I expect to but its a ....* to pull. Does anyone have a recommendation for a warmer vape tank that works well with the MVP2? I really don't like cool hit of the MPT2. I want a warm vape like my triton on my MVP. I think thats why I am not as impressed is I am missing my warm vape.
Ok update, I took Iclear apart and trying to figure out whats wrong. This may be dumb, but remember I have only used tritons who come in the mail ready to use. Is the rubber tip on end of coil supposed to come off? When I take it off and pull on without juice it pulls fine, with it (without juice it goes back to being very hard to pull. Thanks.
I am pretty sure that plastic tip is suppose to be on there. I was watching some cleaning video's yesterday and they all said dont forget to put that back on.
Dont know what it does though.
Dont know what it does though.
Yeah I just watched video for it, and saw it was on there. I think it is to help not get juice down the hole, not sure though. I just don't get it. I have tried putting on all different ways it just is super tight with it on. So no one else had this issue?
The I clear does not generally have a tight draw. I am going to take a guess here that you may have filled it right up to the top. They 30's don't like being filled up all the way. Try using half a tank. Also, before you start pulling on the half tank, with the Iclear off the device, hold a tissue over the end and blow real hard. This will clear excess juice. I suspect your device is flooding.
Yes, the plastic cap keeps the juice from going down the air hole when inverted.
The I16 is a REAL warm vape and works well on the MVP but has a small tank and drinks up juice like the 30 does. My personal favorite is the Kanger T2. Nice warm top coil vape and it just plain works. Unfortunately, I have to use a 510-ego connector to avoid air flow problems but I don't find the adapter to be any kind of problem.
Yes Luv, remove the rubber tip that came on your iClear 30 drip tip =]
Another issue could be that the bottom is not notched properly, it needs to be notched so that air can get through.
A final thing that I've found is that I've screwed it down too tightly.
Last edited:
Can you post a pic? The tank shouldn't have resistance when its not screwed onto anything. Sounds like something is blocking the air-hole. I think one option would be to start over and re-assemble the tank after cleaning all the components.
that silicone cup is to seal off the fluid in the tank
from coming out the mouthpiece-it has to be there...
hate to tell ya, but you need to clean it out-remove coil and see what
it going on--can you blow thru it while in hand, can you see a blockage ?
just don't know what else to tell ya
it is the iClear30 (not 30S) right
from coming out the mouthpiece-it has to be there...
hate to tell ya, but you need to clean it out-remove coil and see what
it going on--can you blow thru it while in hand, can you see a blockage ?
just don't know what else to tell ya
it is the iClear30 (not 30S) right
this MVP not sure which version I have. I got a couple of months ago as I wanted to get away from the disposables and the cig-a-like was not cutting it for me. I have a an i30 and a protank2 as well as a couple of tanks. I am very pleased with it. I would recommend this to anyone. Talk about durable I am a mechanic and well it does find its way into my tool box from time to time and a wrench or two might have went as said hi. needless to say i think it has one very very minor scratch on it (you have to look close to find it) been thinking about getting one to gut and put in a home made brass box just for looks but well see its still in the back of my mind thinking about it stages im more focused on DYI juice right now to take on that project
Ok so I did blow on it and it helped get the gurgling to go away(it was not gurgling on the first fill just tight pull) I took it apart cleaned it put it back together and filled. I think it was gurgling bc I didn't let it dry. It is still very tight. It is very tight when I emptied it and it had no juice in it, so I am not sure if it was due to over filling(which I also did 2nd time) flavor and vapor is there its just very hard to pull. I think I am going to pick up a couple T2's tomorrow. I am hoping they have them at my B&M. I just tried to put beauty ring back on and could not hit at all. I am not sure if that means anything but I figure it may to people who know more than me.
I would try to keep vaping it and see what happens. It may break in.
In the mean time, may be, just maybe, the air holes got clogged some how. Try taking the smallest sewing needle you have and passing it through the little air holes that are just above the 510 threads right above the slots on the bottom of the clearo. Perhaps something got in there an is blocking one or both up.
If you go to the B+M, make sure to pick up a 510-ego connector, they are a good thing to have kicking around and are only a few $. The smallest beauty ring covers the adapter well to make it look good.
hehe wow! The Wii remote strap does actually make a pretty decent wrist strap for the MVP 2. =:3
- Status
Similar threads
