NEW RoyalSmokers C-E2 R4 Review, Tips, Info, Help, Video

[Weekend_warrior1999]

Not to mention if you could use one, Just 1 bought at wally world would make like several hundred prolly

 

[ScottB]

btw - it's not nuked water - then soak. It's a container with the units in it - all held vertically - filled with water, then put into the microwave and nuked for 3 min. Full rolling boil for the last minute or minute-fifteen.

 

[BanjoMan]

Were there any issues at all with taste with that?

Some of the R2's had glue issues, but the plastic cup/filler ring never had any issues that I know of. People were nervous the things might melt but I've never seen or heard of it happening.

 

[dannoman]

Where do you get a dropper like that...that would be nice as it seems like you could nuzzle somethign that size down a little more between the carto wall and the cup...when I drip fill my VG juice it oftentimes dollops into the cup...and good point on condensation surface area on an inverted filler ring...

 

[Weekend_warrior1999]

you do realize you are gonna burn your house down like that..... metal+microwave=FIRE from burning microwave.

 

[Weekend_warrior1999]

But at least you might get a pretty light show first, lol

 

[BanjoMan]

I use the inverted filler ring because it will collect condensate far better than the middle ring. With my extension, there is a lot of condensate – and it winds up in the stem if I use the flat ring.

I’ve filled them so many times that it’s easy. I use a small dropper from a 3 mil sample bottle I got somewhere a while back. 4 full droppers. Done.


Leaks?
Man, you guys are fast. No. No leaking. I carry these things around in my case all day. The worst that happens is my thin juices will work their way into the slits & stem, but one good stiff drag empties that out.

I've tried just the filler ring upside-down and I haven't had your luck. I can't say it's worse than using the middle ring but I didn't see much difference between the two.

 

[badkolo]

just so you know, the tankomizer will not work with 90% of your mods, the center post is recessed in deeply.

im going to send them to turbo,v1john and br and banjo and nav is he is still alive and they can judge for them selves, if you guys want ill make a video of the tankomizer then take it down after you guys see it. they are overly priced since you can make the same bottom with a 1 buck e2, so i dont know why they are charging so much for these.

 

[v1John]

Or use wire mesh from McMasterCarr for the wick, and wire mesh outside the cup for ptb?

 

[v1John]

just so you know, the tankomizer will not work with 90% of your mods, the center post is recessed in deeply.

im going to send them to turbo,v1john and br and banjo and nav is he is still alive and they can judge for them selves, if you guys want ill make a video of the tankomizer then take it down after you guys see it. they are overly priced since you can make the same bottom with a 1 buck e2, so i dont know why they are charging so much for these.

thanks, but no thanks, Bad. Save the shipping. I do need more E2s though.

 

[br5495]

just so you know, the tankomizer will not work with 90% of your mods, the center post is recessed in deeply.

im going to send them to turbo,v1john and br and banjo and nav is he is still alive and they can judge for them selves, if you guys want ill make a video of the tankomizer then take it down after you guys see it. they are overly priced since you can make the same bottom with a 1 buck e2, so i dont know why they are charging so much for these.

No need to make a video for me, bad. I knew what that thing would do before you put juice in it, heheh.

 

[Weekend_warrior1999]

The problem with wire mesh is that it would change the resistance of the coil... as far as the circuit is concerned the wire mesh just became part of the coil in a sense making it HUGE. and raising the resistance which in turn would mean you would more then likely get no vapor cause the entire contraption wouldnt heat up. just a dead battery after a while.

 

[BanjoMan]

bad, don't waste the postage sending me one. I trust your review of them.


Edit: Make sure you send br one, though. No telling what he'll MacGyver it into...

 

[ScottB]

bad, just finish up your ptb's & send me some. Don't waste any more time. No tanko-video. Just do it...

 

[v1John]

The problem with wire mesh is that it would change the resistance of the coil... as far as the circuit is concerned the wire mesh just became part of the coil in a sense making it HUGE. and raising the resistance which in turn would mean you would more then likely get no vapor cause the entire contraption wouldnt heat up. just a dead battery after a while.

not really, the wire mesh is heated first, and also the coil, once you dry burn it it turns into convoluted black nichrome
that's why I can take and squeeze my loops together and it still works the same. The black might keep it insulated.
Otherwise the raidy mods wouldn't work either.


I agree with Scott, these tankotraptions are distracting progress

 

[Weekend_warrior1999]

Thought the ptb mod had already been done. or is this another your talking about.

 

[Weekend_warrior1999]

I'll have to check on the raidy mod.... heard it mentioned... but haven't seen it.

 

[badkolo]

well someone is gonna get them cause i cant have dead weight just sitting here, i started unloading the r3's i had for the same reason until the syringe and br mod where invented

 

[BanjoMan]

well someone is gonna get them cause i cant have dead weight just sitting here, i started unloading the r3's i had for the same reason until the syringe and br mod where invented

Guess there's no chance the guy might take the un-used ones back? Maybe get some of your money back?

 

[br5495]

well someone is gonna get them cause i cant have dead weight just sitting here, i started unloading the r3's i had for the same reason until the syringe and br mod where invented

Maybe we can make an upside down Tankomizer out of it, heheh.

With SS mesh